INCH-POUND MIL-M-38510/762B 6 May 2005 SUPERSEDING MIL-M-38510/762A 14 October 1997 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, ADVANCED CMOS, MULTIPLEXERS, MONOLITHIC SILICON, POSITIVE LOGIC Reactivated after 06 May 2005 and may be used for new and existing designs and acquisitions This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product herein shall consist of this specification sheet and MIL-PRF 38535 1. SCOPE 1.1 Scope. This specification covers the detail requirements for monolithic silicon, advanced CMOS, logic microcircuits. Two product assurance classes and a choice of case outlines, lead finishes, and radiation hardness assurance (RHA) are provided and are reflected in the complete Part or Identifying Number (PIN). For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535 (see 6.3). 1.2 Part or identifying number (PIN). The PIN is in accordance with MIL-PRF-38535 and as specified herein. 1.2.1 Device types. The device types are as follows: Device type Circuit 01 Eight input multiplexer 02 Dual 4-input multiplexer 03 Quad two-input multiplexer 04 Quad two-input multiplexer with inverted outputs 05 Eight-input multiplexer with three-state outputs 06 Dual four-input multiplexer with three-state outputs 07 Quad two-input multiplexer with three-state outputs 08 Quad two-input multiplexer with inverted three-state outputs 1.2.2 Device class. The device class is the product assurance level as defined in MIL-PRF-38535. 1.2.3 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 Flat pack Z GDFP1-G16 16 Flat pack with gull wing 2 CQCC1-N20 20 Square leadless-chip-carrier Comments, suggestions, or questions on this document should be addressed to: Commander, Defense Supply Center Columbus, ATTN: DSCC-VAS, P.O. Box 3990, Columbus, OH 43218-3990, or email mailto:CMOS dscc.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at MIL-M-38510/762B 1.3 Absolute maximum ratings. 1/ 2/ Supply voltage range (V )........................................................................................ -0.5 V dc to +6.0 V dc CC DC input voltage range (V ) ...................................................................................... -0.5 V dc to V + 0.5 V dc IN CC DC output voltage range (V ) ................................................................................. -0.5 V dc to V + 0.5 V dc OUT CC Clamp diode current (I , I ) ..................................................................................... 20 mA IK OK DC output current (I ) ............................................................................................. 50 mA OUT DC V or GND current (I , I ) ............................................................................. 100 mA CC CC GND Storage temperature range (T ) ............................................................................. -65C to +150C STG Maximum power dissipation (P ) ............................................................................... 300 mW D Lead temperature (soldering, 10 seconds) ................................................................ +300C Thermal resistance, junction-to-case ( )................................................................. See MIL-STD-1835 JC Junction temperature (T ) .......................................................................................... +175C J Case operating temperature range (T )..................................................................... -55C to +125C C 1.4 Recommended operating conditions. 2/ 3/ 4/ Supply voltage range (V )........................................................................................ +3.0 V dc to +5.5 V dc CC Input voltage range (V ) ............................................................................................ +0.0 V dc to V IN CC Output voltage range (V )....................................................................................... +0.0 V dc to V OUT CC Case operating temperature range (T )..................................................................... -55C to +125C C Maximum low level input voltage(V ) ........................................................................ 0.90 V dc at V = 3.0 V dc IL CC 1.35 V dc at V = 4.5 V dc CC 1.65 V dc at V = 5.5 V dc CC Minimum high level input voltage (V )....................................................................... 2.10 V dc at V = 3.0 V dc IH CC 3.15 V dc at V = 4.5 V dc CC 3.85 V dc at V = 5.5 V dc CC Input rise and fall rate (t , t ) maximum: r f V = 3.6 V, V = 5.5 V ......................................................................................... 8 ns/V CC CC 1.5 Radiation features. Device types 01, 02, 03, and 07: Total dose (dose rate = 50 300 rads (Si)/s).......................................................... 100 krads (Si) 2 Single Event Latch-up (SEL) .................................................................................. 120 MeV-cm /mg 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. The maximum junction temperature may be exceeded for allowable short duration burn-in screening conditions in accordance with MIL-PRF-38535. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ Operation from 2.0 V dc to 3.0 V dc is provided for compatibility with data retention and battery back-up systems. Data retention implies no input transitions and no stored data loss with the following conditions: V 70 percent of V , IH CC V 30 percent of V , V 70 percent of V at 20 A, V 30 percent of V at 20 A. IL CC OH CC OL CC 4/ Unless otherwise specified, the values listed above shall apply over the full V and T recommended operating range. CC C 2