Effective October 2015 Technical Data 4126 Supersedes March 2007 HC8LP Low profile, high current power inductors Applications Multi-phase regulators Voltage Regulator Modules (VRMs) Distributed power systems DC-DC converters Notebook and laptop regulators Desktop and server VRMs and EVRDs Point-of-Load (POL) modules Battery power systems High current power supplies Data networking and storage systems Environmental data Product description Storage temperature range (component): Low profile surface mount inductors designed -40C to +155C for higher speed switch mode applications Operating temperature range: -40C to +155C requiring low voltage, and high current (ambient plus self-temperature rise) Design utilizes high temperature powder iron Solder reflow temperature: J-STD-020D material with a non-organic binder to eliminate compliant thermal aging Inductance range from 0.17 uH to 47.9 uH Current range from 1.7 to 56 Amps Frequency range 1kHz to 500kHz PbHC8LP Technical Data 4126 Effective October 2015 Low profile, high current power inductors Product specifications 3 4 5 l (amps) l (amps) DCR (m) Volt-Sec sat sat 6 1 2 Part number OCL (H) 20% l (amps) 15% 30% maximum 20C (V-s) rolloff rolloff rms HC8LP-R15-R 0.170 29.0 31 56 1.40 7.8 HC8LP-R39-R 0.430 20.2 19 34 2.80 4.7 HC8LP-R75-R 0.830 15.6 13.5 24 4.70 3.4 HC8LP-1R2-R 1.35 12.4 10.1 18.7 7.50 2.6 HC8LP-1R9-R 1.92 10.1 8.7 15.5 11.5 4.1 HC8LP-2R6-R 2.67 8.3 7.4 13.1 17.1 4.8 HC8LP-3R5-R 3.56 6.9 6.4 11.4 24.5 5.6 HC8LP-4R5-R 4.57 6.5 5.6 10.0 27.6 6.3 HC8LP-5R6-R 5.71 5.5 5.1 9.0 38.9 7.1 HC8LP-6R9-R 6.98 5.2 4.6 8.1 42.8 7.8 HC8LP-8R2-R 8.37 4.5 4.2 7.4 58.0 8.6 HC8LP-100-R 9.90 4.3 6.8 3.8 62.9 9.3 HC8LP-150-R 15.2 3.4 3.1 5.5 99.4 11.6 HC8LP-220-R 21.7 2.8 2.6 4.6 149 13.7 HC8LP-330-R 32.1 2.3 2.1 3.8 224 16.8 HC8LP-470-R 47.9 1.8 1.7 3.1 344 20.3 1. Open Circuit Inductance (OCL) Test Parameters: 100kHz, 1.0Vrms, 0.0Adc, +25C 6. Part number definition: HC8LP-XXX-R 2. Irms: DC current for an approximate DT of 40C without core loss. Derating is necessary for AC currents. HC8LP = Product code and size PCB layout, trace thickness and width, air-flow, and proximity of other heat generating components XXX = Inductance value in uH. R = Decimal point. If no R is present then last character equals will affect the temperature rise. It is recommended that the temperature of the part not exceed 155C number of zeros under worst case operating conditions verified in the end application. -R suffix indicates RoHS compliant 3. Peak current for approximately 15% rolloff +20C 4. Peak current for approximately 30% rolloff +20C 5. Applied Volt-Time product (V-s) across the inductor. This value represents the applied V-s at operating frequency necessary to generate additional core loss which contributes to the 40C temperature rise. De-rating of the I is required to prevent excessive temperature rise. The 100% V-us rating is rms equivalent to a ripple current Ip-p of 20% of Isat (30% rolloff option). Dimensionsmm TOP VIEW SIDE VIEW RECOMMENDED PAD LAYOUT 2.70 0 .55 3.5 typ (2 x) 2plcs 10.9 HC8LP-XXX 10.4 Max Max 3.0 typ wwllyy R 2plcs 4.0 typ 10.4 Max FRONT VIEW Dimesional Table SCHEMATIC A B FRONT VIEW PN C ref max L 1 mm mm R15 2.1 3.5 B R39 2.1 3.5 Max R75 2.1 3.5 1R232.1 .3 1R9 2 Aref thru 2.7 3.5 3.95 470 2plcs ref Part marking: HC8LP= (Product code and size)-xxx=(inductance value in uH, R= decimal point. If no R is present then last character equals number of zeros. wwlyly=date code, R=revision level Tolerances are 0.2 millimeters unless stated otherwise All soldering surfaces to be coplanar within 0.1 millimeters Do not route traces or vias underneath the inductor www.eaton.com/elx 2