4114NXU

Operating manual 1 SAFETY REGULATIONS AND INFORMATION 4114 NXU Read the operating manual carefully before commencing work at the product. Pay attention to the following warnings to avoid risk to persons or malfunctioning. This operating manual is an integral part of the product. In the event of resale or change of ownership the operating manual must accompany the product. This operating manual may be copied and provided as information on potential risks and their avoidance. Hazard classification of warning notices The following risk ratings are used in this operating manual to denote potential risk situations and important safety instructions: DANGER This is a potentially dangerous situation Product type, manufacturing date (calendar week/year of construction) and warns of an impending health risk and if required, conformity mark can be found on the nameplate on the or risk of fatal injury if this warning is product. not observed. Observe this warning. Please provide us with the contents of the nameplate when making WARNING enquiries about the product. The dangerous situation can occur and can result in major or fatal injuries if the ebm-papst St.Georgen GmbH & Co. KG warning is not observed. Work with Hermann-Papst-Strae 1 extreme care. D - 78112 St.Georgen CAUTION The dangerous situation can occur and Phone: +49 (0) 7724 / 81-0 can result in minor injuries or damage Fax: +49 (0) 7724 / 81-1309 to property if the warning is not observed. info2 de.ebmpapst.com NOTE www.ebmpapst.com A potentially dangerous situation can occur and results in damage to As per: 04.02.2013 property if not avoided. Version 1 4 Article number: 9294310177 Qualification of personnel Only skilled electricians are permitted to install the product, to carry out Original operating manual the test run and to work at the electrical unit. Only instructed and authorized skilled personnel are permitted to INDEX transport, unpack, operate and service the product. Basic safety regulations 1 SAFETY REGULATIONS AND INFORMATION 1 Safety risks related to the product must be reassessed after installing in the final device. 2 INTENDED USE 2 The operating manual was developed in accordance with European market requirements and may need adapting to the market requirements of the country in question. 3 TECHNICAL DATA 3 When working at the product, observe the following: 4 CONNECTION AND COMMISSIONING 3 Do not make any changes to the product. WARNING 5 FAULTS, POSSIBLE CAUSES AND REMEDIES 4 Impermissible high load Stop the product immediately after 6 APPROVALS 4 impermissible loading (e.g. impact, heat, overvoltage). page 1 of 5 Electrical voltage and current Store the product in a dry and clean environment that is well protected. DANGER Ensure that the storage temperature is adhered to,see Chapter 3, Electrical voltage Technical Data.If the product is not operated for a longer period of time, we recommend running it for approx. 15 minutes annually to Regularly check the electrical move the motor bearings. equipment of the product. Eliminate immediately loose Cleaning connections and defective cables. Safety and protective functions NOTE Product damaged during cleaning DANGER Missing safety device and faulty Do not clean the product using a protective equipment. water jet or pressure washer. Do not put any pressure on the rotor. Without protective equipment severe Do not use cleaning agents injuries can occur, e.g. by taking hold of containing acids, caustic solutions the rotating equipment. or solvents. Operate the product with protection guards only. Electromagnetic radiation Disposal Electromagnetic compatibility (EMC) may affect the system integration When disposing of the product, observe all requirements and of the product due to interaction. regulations that are relevant in your country. Ensure the electromagnetic compatibility of the entire system. 2 INTENDED USE Moving parts The product is designed exclusively as a built-in device for conveying DANGER air according to the technical data. Self-starting product Every use that is not in accordance with the intended purpose, is regarded as misuse of the product. If voltage is applied, the motor On-site installations must comply with the mechanical, thermal and automatically restarts after a mains service life requirements, see Chapter 3, Technical Data. failure or when blocking has been eliminated. Intended use includes: Do not stand in the danger zone of the product. - Operating the product with all protective equipment Switch off the mains voltage when - Do not put the product into operation before it has been installed in working on the product and secure the customer s application against switching on again. - Observation of the operating manual WARNING Rotating fan Use for other than the intended purpose Using the product for the purposes mentioned below is prohibited and Long hair, loose-fitting garments and can be dangerous: jewellery can be caught and pulled into the product. Risk of injury. - Conveyance of air that contains abrasive particles. Do not wear loose-fitting garments - Conveyance of air that has a highly corrosive effect. or jewellery when working on - Conveyance of air that has a high dust load, e.g. vacuuming moving parts. sawdust. Protect long hair by wearing a hair - Conveyance of inflammable gases/particles. net. - Contact with materials that can damage the product, e.g. acids, caustic solutions, solvents. CAUTION - Exposure to radiation that can damage product components, e.g. High risk of fire spreading strong UV rays or thermal radiation. - Operating during external vibration. Can cause fire to spread. Never direct the airflow - Operating the product close to inflammable materials or components. (intake/exhaust side) at a potential - Operating the product in an explosive atmosphere source of fire. - Use of the prouct as a safety component or for performing safety- relevant functions. Hot surface - Operating in medical devices with life-sustaining or life-saving function. CAUTION - Operating in non-stationary systems, e.g. railway vehicles, aircraft High temperature at motor housing. and spacecraft. Risk of burns - Operating with fully or partially dismantled or manipulated protective equipment. Provide adequate protection against - Operating the product under conditions other than those mentioned accidental contact. in the technical data. - Furthermore, all fields of application not mentioned under intended Transport use. Only transport the product in its original packaging. Secure during An in situ assessment must be conducted of the heating behavior transport. (appropriate and inappropriate operation), the protection against The vibration values, temperature and climate ranges should not be contact, electrical shocks, impact of foreign objects or water and the exceeded during transport. usage at altitudes higher than 2000 meters. Storage Contact ebm-papst if you have specific queries regarding the product. page 2 of 5