M1G055-BD91-26 Operating instructions ebm-papst Mulfingen GmbH & Co. KG 1. SAFETY REGULATIONS AND NOTES Bachmhle 2 Please read these operating instructions carefully before starting to work D-74673 Mulfingen with the device. Observe the following warnings to prevent malfunctions Phone +49 (0) 7938 81-0 or physical damage to both property and people. Fax +49 (0) 7938 81-110 These operating instructions are to be regarded as part of this device. info1 de.ebmpapst.com If the device is sold or transferred, the operating instructions must www.ebmpapst.com accompany it. CONTENTS These operating instructions may be duplicated and forwarded for information about potential dangers and their prevention. 1. SAFETY REGULATIONS AND NOTES 1 1.1 Levels of hazard warnings 1.1 Levels of hazard warnings 1 These operating instructions use the following hazard levels to indicate 1.2 Staff qualification 1 potentially hazardous situations and important safety regulations: 1.3 Basic safety rules 1 DANGER 1.4 Electrical voltage 1 Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Compliance with 1.5 Electromagnetic radiation 2 the measures is mandatory. 1.6 Mechanical movement 2 WARNING 1.7 Hot surface 2 Indicates a potentially hazardous situation which, if not avoided, 1.8 Transport 2 could result in death or serious injury. Exercise extreme 1.9 Storage 2 caution while working. 1.10 Disposal 2 CAUTION Indicates a potentially hazardous situation which, if not avoided, 2. PROPER USE 3 may result in minor or moderate injury or damage of property. 3. TECHNICAL DATA 4 NOTE 3.1 Product drawing 4 A potentially harmful situation can occur and, if not avoided, can lead to property damage. 3.2 Nominal data 5 3.3 Technical features 5 1.2 Staff qualification 3.4 Mounting data 5 The device may only be transported, unpacked, installed, operated, 3.5 Transport and storage conditions 5 maintained and otherwise used by qualified, trained and authorised technical staff. 4. CONNECTION AND START-UP 6 Only authorised specialists are permitted to install the device, to carry 4.1 Connecting the mechanical system 6 out a test run and to perform work on the electrical installation. 4.2 Connecting the electrical system 6 1.3 Basic safety rules 4.3 Connection screen 7 Any safety hazards stemming from the device must be re-evaluated 4.4 Checking the connections 8 once it is installed in the end device. 4.5 Switch on device 8 Observe the following when working on the unit: 4.6 Switching off the device 8 Do not make any modifications, additions or conversions to the device without the approval of ebm-papst. 5. INTEGRATED PROTECTIVE FUNCTIONS 8 1.4 Electrical voltage 6. MAINTENANCE, MALFUNCTIONS, POSSIBLE 9 CAUSES AND REMEDIES Check the electrical equipment of the device at regular intervals, refer 6.1 Cleaning 9 to chapter 6.2 Safety test. Replace loose connections and defective cables immediately. 6.2 Safety test 9 DANGER Electrical load on the device Risk of electric shock Stand on a rubber mat if you are working on an electrically charged device. CAUTION In the event of failure, there is electric voltage at the rotor and impeller The rotor and impeller are base insulated. Do not touch the rotor and impeller once they are installed. Item no. 50356-5-9970 Revision 82830 Release 2014-04-23 Page 1 / 9 ebm-papst Mulfingen GmbH & Co. KG Bachmhle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 info1 de.ebmpapst.com www.ebmpapst.com Translation of the original operating instructionsM1G055-BD91-26 Operating instructions CAUTION 1.7 Hot surface If control voltage is applied or a speed setpoint is stored, CAUTION the motor automatically restarts, e.g. after a power failure. High temperature at the electronics enclosure Danger of injury Danger of burn injuries Keep out of the danger zone of the device. Ensure that sufficient protection against accidental contact is When working on the device, switch off the mains provided. supply voltage and secure the latter from being switched on again. 1.8 Transport Wait until the device stops. CAUTION After working on the device, remove any used tools or Transport of motor other objects from the device. Crushing hazard CAUTION Wear safety shoes and cut-resistant safety gloves. The motor restarts automatically when operating voltage Transport the motor in its original packaging only. is applied, e.g. after a power failure. Secure the device so that it does not slip, e.g. by using a Danger of injury clamping strap. Keep out of the danger zone of the motor. When working on the motor, switch off the mains supply 1.9 Storage voltage and secure the latter from being switched on again. Store the device, partially or fully assembled, in a dry and Wait until the motor stops. weatherproof manner in the original packing in a clean environment. Protect the device from environmental impacts and dirt until the final 1.5 Electromagnetic radiation installation. Interference from electromagnetic radiation is possible, e.g. in conjunction We recommend storing the device for a maximum up to one year to with open and closed-loop control devices. guarantee proper operation and longest possible service life. If unacceptable emission intensities occur when the fan is installed, Even devices explicitly suited for outdoor use are to be stored as appropriate shielding measures have to be taken by the user. described prior to being commissioned. NOTE Maintain the storage temperature, see Electrical or electromagnetic interferences after chapter 3.5 Transport and storage conditions. integrating the device in installations on the customer s side. 1.10 Disposal Verify that the entire setup is EMC compliant. When disposing of the device, please comply with all relevant requirements and regulations applicable in your country. 1.6 Mechanical movement WARNING Rotating device Long hair, loose items of clothing and jewellery could become entangled and pulled into the device. You could be injured. Do not wear any loose clothing or jewellery while working on rotating parts. Protect long hair by wearing a cap. WARNING Flying parts If the motor is operated with attached fan blades, missing safety devices may cause balancing weights or broken fan blades to be ejected and cause bodily injuries. Take the appropriate safety measures e.g. install guard grilles. Keep out of the exhaust zone. Item no. 50356-5-9970 Revision 82830 Release 2014-04-23 Page 2 / 9 ebm-papst Mulfingen GmbH & Co. KG Bachmhle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 info1 de.ebmpapst.com www.ebmpapst.com Translation of the original operating instructions