S3000-M24-48 ebm papst

5246 PAPST cat REPRO 6/9/00 4:01 pm Page 15 thermal management systems Speed Control Alarm Functions and Outputs Temperature dependent speed control is In the event of the measured temperature provided for any number of PAPST DC fans or exceeding the upper selected level T2, a dual blowers up to a total power capacity of 65W. output alarm is activated, one output in the form of a single pole change-over relay with The control module makes use of up to volt-free contacts and the other as an open 4 thermistors which can be located in the most collector. The same dual alarm arrangement is heat sensitive areas within the equipment. provided in the event of a thermistor failure. The module provides linear control between An open collector output is also provided half and full speed. This is achieved by utilising should the module switch to shutdown/ one of the four user selected temperature standby mode. programs available which sets temperature system 3000 control module parameters T1 (lower level) and T2 (upper Features Description level). As the surrounding ambient temperature The System 3000 Module offers The System 3000 is a comprehensive solution rises, the module responds to the highest advanced control for thermal management for the control and monitoring of PAPST DC temperature recorded by any one of the systems providing: thermistors. In the event of a thermistor failure, fans, together providing a thermal management Temperature dependant speed control the fans will run at full speed for fail safe system for electronic equipment. It offers Multiple point temperature sensing a modular approach enabling the Control operation. A shutdown and stand-by mode for Can control any number of fans or blowers Module to function as a separate fan speed low temperatures (T0) is also available which is up to 65W total power consumption controller or as a complete system integrated particularly useful for equipment exposed to Modules available for 12, 24 or 48VDC with the Monitor Module. very cold ambient temperatures outdoors. PAPST fans Alarm outputs for over temperature and thermistor fail 155 System 3000 Low temperature fan shutdown/ Terminal connections 38 monitor module standby mode 63 175 Up to 65W of System 3000 PAPST DC fans Fail safe operation for thermistor fail control module 165 or blowers M3.5 hole Operates as a stand-alone controller 4 places 50 1 3 5 7 9 31 32 2 4 6 8 or can be combined with System 3000 Relay LED or open collector Monitor Module. Alarm outputs All I/O connections are via screw terminals Protection: reverse polarity and power limiting on 5V supply Ordering Information Operating temperature range: 0 - 70C Part No. Description EMC compliance to EN50081-1:1992 S3000-C12 PAPST System 3000 Switch Mode Control Module 12VDC EN61000-4-3:1996 & EN61000-4-2:1995. S3000-C24 PAPST System 3000 Switch Mode Control Module 24VDC S3000-C48 PAPST System 3000 Switch Mode Control Module 48VDC All measurements in mm. Papst plc East Portway Andover Hampshire SP10 3RT Tel +44 (0)1264 333388 Fax +44 (0)1264 332182 www.papstplc.com Fit it. Forget it.5246 PAPST cat REPRO 6/9/00 4:01 pm Page 16 thermal management systems Alarm Functions and Outputs Individual fan alarm output system 3000 monitor One set of single pole change-over volt-free Supports 12, 24 or 48VDC PAPST fans module contacts provide an alarm indication should Several fan fail threshold settings available Description any fan fall below the selected speed threshold. Easy to integrate and connect to equipment The system 3000 is a comprehensive solution Each of the six fans has a corresponding Operates as a stand-alone monitor for the control and monitoring of PAPST DC open collector alarm output. Each output will or can be combined with System 3000 fans, together providing a thermal management become independently active if the speed Control Module. system for electronic equipment. It offers a of its related fan falls below the selected All I/O connections are via screw terminals modular approach enabling the Monitor threshold. These outputs can be used to drive Protection: reverse polarity and power Module to function as a separate monitoring LEDs if required in conjunction with the 5VDC limiting on 5V supply unit or as a complete system integrated with integral logic supply. Operating temperature range 0 to 70C the Control Module. EMC compliance to EN50081-1:1992 Features Fan Monitoring EN61000-4-3:1996 & EN61000-4-2:1995 The System 3000 Monitor Module offers The unit provides fan failing monitoring for advanced monitoring for thermal management up to 6 PAPST DC fans or blowers fitted with systems providing: open collector (/ 2) or TTL (/12) sense wires. Monitoring for up to 6 PAPST DC fans If the speed of any fan falls below one of the or blowers user selectable thresholds an alarm will Alarm outputs for direct or remote be triggered. fan status 155 System 3000 Terminal connections 38 control module 175 63 Up to 6 PAPST System 3000 DC fans or monitor module 165 blowers M3.5 hole 4 places 50 2 4 6 8 31 1 3 5 7 32 Relay LED or open collector Alarm outputs Ordering Information Part No. Description S3000-M12 PAPST System 3000 Monitor Module 12VDC S3000-M24-48 PAPST System 3000 Monitor Module 24-48VDC All measurements in mm. Papst plc East Portway Andover Hampshire SP10 3RT Tel +44 (0)1264 333388 Fax +44 (0)1264 332182 www.papstplc.com Fit it. Forget it.