W1G200-EC95-47
Operating instructions
ebm-papst Mulfingen GmbH & Co. KG
1. SAFETY REGULATIONS AND INFORMATION
Bachmhle 2
Read these operating instructions carefully before starting work on the
D-74673 Mulfingen
device. Observe the following warnings to prevent malfunctions or
Phone +49 (0) 7938 81-0
danger to persons.
Fax +49 (0) 7938 81-110
These operating instructions are to be regarded as part of the device.
info1@de.ebmpapst.com
The device is only to be sold or passed on together with the operating
www.ebmpapst.com
instructions.
CONTENTS
These operating instructions may be duplicated and distributed to inform
about potential dangers and their prevention.
1. SAFETY REGULATIONS AND INFORMATION 1
1.1 Hazard levels for warnings
1.1 Hazard levels for warnings 1
These operating instructions use the following hazard levels to indicate
1.2 Staff qualifications 1
1.3 Basic safety rules 1 potentially hazardous situations and important safety regulations:
1.4 Voltage 1
DANGER
1.5 Safety and protective features 2
Indicates an imminently hazardous situation which will result in
1.6 Electromagnetic radiation 2
death or serious injury if the specified actions are not taken.
1.7 Mechanical movement 2
Compliance with the instructions is imperative.
1.8 Emissions 2
1.9 Transport 2 WARNING
Indicates a potentially hazardous situation which can result in
1.10 Storage 2
death or serious injury if the specified actions are not taken.
2. INTENDED USE 3
Exercise extreme caution while working.
CAUTION
3. TECHNICAL DATA 4
Indicates a potentially hazardous situation which can result in
3.1 Product drawing 4
minor or moderate injury or damage to property if the specified
3.2 Nominal data 5
actions are not taken.
3.3 Technical description 5
3.4 Mounting data 5
NOTE
3.5 Transport and storage conditions 5
A potentially harmful situation can occur and, if not avoided, can
3.6 Electromagnetic compatibility 5
lead to property damage.
4. CONNECTION AND STARTUP 6
1.2 Staff qualifications
4.1 Mechanical connection 6
The device may only be transported, unpacked, installed, operated,
4.2 Electrical connection 6
maintained and otherwise used by suitably qualified, trained and
4.3 Routing of cables 6
authorized technical staff.
4.4 Connection diagram 8
Only authorized specialists are permitted to install the device, to carry
4.5 Checking connections 9
out a test run and to perform work on the electrical installation.
4.6 Switching on the device 9
4.7 Switching off the device 9
1.3 Basic safety rules
5. INTEGRATED PROTECTIVE FEATURES 9
The safety hazards associated with the device must be assessed again
following installation in the final product.
6. MAINTENANCE, MALFUNCTIONS, POSSIBLE 9
The locally applicable industrial safety regulations are always to be
CAUSES AND REMEDIES
observed when working on the device.
6.1 Cleaning 10
Keep the workplace clean and tidy. Untidiness in the work area
6.2 Safety inspection 10
increases the risk of accidents.
6.3 Disposal 10
Note the following when working on the device:
; Do not perform any modifications, additions or conversions on the
device without the approval of ebm-papst.
1.4 Voltage
; Check the device's electrical equipment at regular intervals; see
Chapter 6.2 Safety inspection.
; Replace loose connections and defective cables immediately.
DANGER
Electrically charged device
Risk of electric shock
When working on an electrically charged device, stand on a
rubber mat.
Item no. 50083-5-9970 ENU Change 205985 Approved 2019-10-29 Page 1 / 11
ebm-papst Mulfingen GmbH & Co. KG Bachmhle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 info1@de.ebmpapst.com www.ebmpapst.com
Translation of the original operating instructionsW1G200-EC95-47
Operating instructions
WARNING
1.8 Emissions
Live terminals and connections even with device
WARNING
switched off
Depending on the installation and operating conditions,
Electric shock
the sound pressure level may exceed 70 dB(A).
Wait five minutes after disconnecting the voltage at all poles
Risk of noise-induced hearing loss
before opening the device.
Take appropriate technical safety measures.
CAUTION
Protect operating personnel with appropriate safety
If control voltage or a stored speed set value is applied,
equipment such as hearing protection.
the motor will restart automatically, e.g. after a power
Also observe the requirements of local agencies.
failure.
Risk of injury
1.9 Transport
Keep out of the devices danger zone.
NOTE
When working on the device, switch off the line voltage
Transporting the device
and ensure that it cannot be switched back on.
Transport the device in its original packaging only.
Wait until the device comes to a stop.
After working on the device, remove any tools or other
1.10 Storage
objects from the device.
; Store the device, partially or fully assembled, in a dry place,
1.5 Safety and protective features
protected against the weather and free from vibration, in the original
packaging in a clean environment.
DANGER
; Protect the device against environmental effects and dirt until final
Guard missing and guard not functioning
installation.
Without a guard, hands may become caught up in the device
; We recommend storing the device for no longer than one year in
during operation for example, resulting in serious injury. Loose
order to guarantee trouble-free operation and the longest possible
parts or items of clothing could be drawn in.
service life.
The device is a built-in component. As the owner, you are
; Even devices explicitly intended for outdoor use are to be stored as
responsible for ensuring that the device is adequately
described prior to commissioning.
safeguarded.# Operate the device only with a fixed
protective device and guard grill.
; Maintain the storage temperature, see
Chapter 3.5 Transport and storage conditions.
Stop the device immediately if a protective device is
found to be missing or ineffective.
1.6 Electromagnetic radiation
Interference from electromagnetic radiation is possible, e.g. in conjunction
with open- and closed-loop control devices.
If impermissible radiation levels occur following installation, appropriate
shielding measures have to be taken by the user.
NOTE
Electrical or electromagnetic interference after installing
the device in customer equipment.
Verify that the entire setup is EMC-compliant.
1.7 Mechanical movement
DANGER
Rotating device
Risk of injury to body parts coming into contact with the rotor or
the impeller.
Secure the device against accidental contact.
Before working on the system/machine, wait until all
parts have come to a standstill.
WARNING
Rotating device
Long hair and dangling items of clothing, jewelry and the like
can become entangled and be pulled into the device. Injuries
can result.
Do not wear any loose-fitting or dangling clothing or jewelry
while working on rotating parts.
Protect long hair with a cap.
Item no. 50083-5-9970 ENU Change 205985 Approved 2019-10-29 Page 2 / 11
ebm-papst Mulfingen GmbH & Co. KG Bachmhle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 info1@de.ebmpapst.com www.ebmpapst.com
Translation of the original operating instructions