W2E200-HH82-01 Operating instructions ebm-papst Mulfingen GmbH & Co. KG 1. SAFETY REGULATIONS AND INFORMATION Bachmhle 2 Read these operating instructions carefully before starting work on the D-74673 Mulfingen device. Observe the following warnings to prevent malfunctions or Phone +49 (0) 7938 81-0 danger to persons. Fax +49 (0) 7938 81-110 These operating instructions are to be regarded as part of the device. info1 de.ebmpapst.com The device is only to be sold or passed on together with the operating www.ebmpapst.com instructions. CONTENTS These operating instructions may be duplicated and distributed to inform about potential dangers and their prevention. 1. SAFETY REGULATIONS AND INFORMATION 1 1.1 Hazard levels for warnings 1.1 Hazard levels for warnings 1 These operating instructions use the following hazard levels to indicate 1.2 Staff qualifications 1 1.3 Basic safety rules 1 potentially hazardous situations and important safety regulations: 1.4 Voltage 1 DANGER 1.5 Safety and protective features 2 Indicates an imminently hazardous situation which will result in 1.6 Mechanical movement 2 death or serious injury if the specified actions are not taken. 1.7 Emissions 2 Compliance with the instructions is imperative. 1.8 Hot surface 2 1.9 Transport 2 WARNING Indicates a potentially hazardous situation which can result in 1.10 Storage 2 death or serious injury if the specified actions are not taken. 2. INTENDED USE 3 Exercise extreme caution while working. CAUTION 3. TECHNICAL DATA 4 Indicates a potentially hazardous situation which can result in 3.1 Product drawing 4 minor or moderate injury or damage to property if the specified 3.2 Nominal data 5 actions are not taken. 3.3 Technical description 5 3.4 Mounting data 5 NOTE 3.5 Transport and storage conditions 5 A potentially harmful situation can occur and, if not avoided, can lead to property damage. 4. CONNECTION AND STARTUP 6 4.1 Mechanical connection 6 1.2 Staff qualifications 4.2 Electrical connection 6 The device may only be transported, unpacked, installed, operated, 4.3 Connection via terminal strip 7 maintained and otherwise used by suitably qualified, trained and 4.4 Connection diagram 8 authorized technical staff. 4.5 Checking connections 9 Only authorized specialists are permitted to install the device, to carry 4.6 Switching on the device 9 out a test run and to perform work on the electrical installation. 4.7 Switching off the device 9 1.3 Basic safety rules 5. MAINTENANCE, MALFUNCTIONS, POSSIBLE 9 CAUSES AND REMEDIES The safety hazards associated with the device must be assessed again 5.1 Cleaning 10 following installation in the final product. 5.2 Safety inspection 10 The locally applicable industrial safety regulations are always to be 5.3 Disposal 10 observed when working on the device. Keep the workplace clean and tidy. Untidiness in the work area increases the risk of accidents. Note the following when working on the device: Do not perform any modifications, additions or conversions on the device without the approval of ebm-papst. 1.4 Voltage Check the device s electrical equipment at regular intervals see Chapter 5.2 Safety inspection. Replace loose connections and defective cables immediately. DANGER Electrically charged device Risk of electric shock When working on an electrically charged device, stand on a rubber mat. Item no. 15702-5-9970 ENU Change 232995 Approved 2021-06-02 Page 1 / 11 ebm-papst Mulfingen GmbH & Co. KG Bachmhle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 info1 de.ebmpapst.com www.ebmpapst.com Translation of the original operating instructionsW2E200-HH82-01 Operating instructions CAUTION 1.7 Emissions Electric charge on capacitor after device is switched off WARNING Electric shock, risk of injury Depending on the installation and operating conditions, Discharge the capacitors before working on the device. the sound pressure level may exceed 70 dB(A). WARNING Risk of noise-induced hearing loss Live terminals and connections even with device Take appropriate technical safety measures. switched off Protect operating personnel with appropriate safety Electric shock equipment such as hearing protection. Wait five minutes after disconnecting the voltage at all poles Also observe the requirements of local agencies. before opening the device. CAUTION 1.8 Hot surface In the event of a fault, the rotor and the impeller will be CAUTION energized High temperature on motor housing The rotor and the impeller have basic insulation. Risk of burns Do not touch the rotor and impeller once installed. Ensure sufficient protection against accidental contact. CAUTION The motor restarts automatically when operating voltage 1.9 Transport is applied, e.g. after a power failure. NOTE Risk of injury Transporting the device Keep out of the device s danger zone. Transport the device in its original packaging only. When working on the device, switch off the line voltage Secure the device so it cannot slip, e.g. by using a and ensure that it cannot be switched back on. lashing strip. Wait until the device comes to a stop. 1.10 Storage 1.5 Safety and protective features Store the device, partially or fully assembled, in a dry place, DANGER protected against the weather and free from vibration, in the original Guard missing and guard not functioning packaging in a clean environment. Without a guard, hands may become caught up in the device Protect the device against environmental effects and dirt until final during operation for example, resulting in serious injury. Loose installation. parts or items of clothing could be drawn in. We recommend storing the device for no longer than one year in The device is a built-in component. As the owner, you are order to guarantee trouble-free operation and the longest possible responsible for ensuring that the device is adequately service life. safeguarded. Operate the device only with a fixed Even devices explicitly intended for outdoor use are to be stored as protective device and guard grill. described prior to commissioning. Stop the device immediately if a protective device is Maintain the storage temperature, see found to be missing or ineffective. Chapter 3.5 Transport and storage conditions. 1.6 Mechanical movement DANGER Rotating device Risk of injury to body parts coming into contact with the rotor or the impeller. Secure the device against accidental contact. Before working on the system/machine, wait until all parts have come to a standstill. WARNING Rotating device Long hair and dangling items of clothing, jewelry and the like can become entangled and be pulled into the device. Injuries can result. Do not wear any loose-fitting or dangling clothing or jewelry while working on rotating parts. Protect long hair with a cap. Item no. 15702-5-9970 ENU Change 232995 Approved 2021-06-02 Page 2 / 11 ebm-papst Mulfingen GmbH & Co. KG Bachmhle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 info1 de.ebmpapst.com www.ebmpapst.com Translation of the original operating instructions