W2E300-CP02-37 Operating instructions ebm-papst Mulfingen GmbH & Co. KG 1. SAFETY REGULATIONS AND NOTES Bachmhle 2 Please read these operating instructions carefully before starting to work D-74673 Mulfingen with the device. Observe the following warnings to prevent malfunctions Phone +49 (0) 7938 81-0 or physical damage to both property and people. Fax +49 (0) 7938 81-110 These operating instructions are to be regarded as part of this device. info1 de.ebmpapst.com If the device is sold or transferred, the operating instructions must www.ebmpapst.com accompany it. CONTENTS These operating instructions may be duplicated and forwarded for information about potential dangers and their prevention. 1. SAFETY REGULATIONS AND NOTES 1 1.1 Levels of hazard warnings 1.1 Levels of hazard warnings 1 These operating instructions use the following hazard levels to indicate 1.2 Staff qualification 1 1.3 Basic safety rules 1 potentially hazardous situations and important safety regulations: 1.4 Electrical voltage 1 DANGER 1.5 Safety and protective functions 2 Indicates an imminently hazardous situation which, if not 1.6 Electromagnetic radiation 2 avoided, will result in death or serious injury. Compliance with 1.7 Mechanical movement 2 the measures is mandatory. 1.8 Emission 2 1.9 Hot surface 2 WARNING Indicates a potentially hazardous situation which, if not avoided, 1.10 Transport 2 could result in death or serious injury. Exercise extreme 1.11 Storage 2 caution while working. 2. PROPER USE 3 CAUTION Indicates a potentially hazardous situation which, if not avoided, 3. TECHNICAL DATA 4 may result in minor or moderate injury or damage of property. 3.1 Product drawing 4 3.2 Nominal data 5 NOTE 3.3 Data according to ErP directive 5 A potentially harmful situation can occur and, if not avoided, can 3.4 Technical features 5 lead to property damage. 3.5 Mounting data 5 3.6 Transport and storage conditions 5 1.2 Staff qualification The device may only be transported, unpacked, installed, operated, 4. CONNECTION AND START-UP 6 maintained and otherwise used by qualified, trained and authorised 4.1 Connecting the mechanical system 6 technical staff. 4.2 Connecting the electrical system 6 Only authorised specialists are permitted to install the device, to carry 4.3 Connection of the cables 6 out a test run and to perform work on the electrical installation. 4.4 Connection screen 7 4.5 Checking the connections 8 1.3 Basic safety rules 4.6 Switch on device 8 4.7 Switching off the device 8 Any safety hazards stemming from the device must be re-evaluated once it is installed in the end device. 5. MAINTENANCE, MALFUNCTIONS, POSSIBLE 8 Observe the following when working on the unit: CAUSES AND REMEDIES Do not make any modifications, additions or conversions to the 5.1 Cleaning 9 device without the approval of ebm-papst. 5.2 Safety test 9 5.3 Disposal 9 1.4 Electrical voltage Check the electrical equipment of the device at regular intervals, refer to chapter 5.2 Safety test. Replace loose connections and defective cables immediately. DANGER Electrical load on the device Risk of electric shock Stand on a rubber mat if you are working on an electrically charged device. WARNING Terminals and connections have voltage even with a unit that is shut off Electric shock Wait five minutes after disconnecting the voltage at all poles before opening the device. Item no. 12161-5-9970 ENG Revision 76115 Release 2012-08-18 Page 1 / 9 ebm-papst Mulfingen GmbH & Co. KG Bachmhle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 info1 de.ebmpapst.com www.ebmpapst.com Translation of the original operating instructionsW2E300-CP02-37 Operating instructions CAUTION Do not wear any loose-fitting or dangling clothing or jewellery In the event of failure, there is electric voltage at the while working on rotating parts. Protect long hair with a cap. rotor and impeller 1.8 Emission The rotor and impeller are base insulated. Do not touch the rotor and impeller once they are installed. WARNING Depending on the installation and operating conditions, CAUTION a sound pressure level greater than 70 dB(A) may arise. The motor restarts automatically when operating voltage Danger of noise-induced hearing loss is applied, e.g. after a power failure. Danger of injury Take appropriate technical safety measures. Keep out of the danger zone of the device. Protect operating personnel with appropriate safety equipment, e.g. hearing protection. When working on the device, switch off the mains supply voltage and secure the latter from being switched on Also observe the requirements of local agencies. again. 1.9 Hot surface Wait until the device stops. CAUTION 1.5 Safety and protective functions High temperature at the motor housing Danger of burn injuries DANGER Protective device missing and protective device not Ensure that sufficient protection against accidental contact is functioning provided. Without a protective device there is a risk of serious injury, for 1.10 Transport instance if the hands reach or are sucked into the device during operation. NOTE Operate the device only with a fixed protective device and Transport of device guard grille. The fixed protective device must be able to Transport the device in its original packaging only. withstand the kinetic energy of a fan blade that becomes Secure the device so that it does not slip, e.g. by using a detached at maximum speed. There must not be any gaps clamping strap. which it is possible to reach into with the fingers, for example. The device is a built-in component. As the operator, you 1.11 Storage are responsible for ensuring that the device is secured Store the device, partially or fully assembled, in a dry and adequately. weatherproof manner in the original packing in a clean environment. Stop the device immediately if a protective device is Protect the device from environmental impacts and dirt until the final found to be missing or ineffective. installation. 1.6 Electromagnetic radiation We recommend storing the device for a maximum up to one year to guarantee proper operation and longest possible service life. Interference from electromagnetic radiation is possible, e.g. in conjunction with open and closed-loop control devices. Even devices explicitly suited for outdoor use are to be stored as If unacceptable emission intensities occur when the fan is installed, described prior to being commissioned. appropriate shielding measures have to be taken by the user. Maintain the storage temperature, see chapter 3.6 Transport and storage conditions. NOTE Electrical or electromagnetic interferences after integrating the device in installations on the customer s side. Verify that the entire setup is EMC compliant. 1.7 Mechanical movement DANGER Rotating device Body parts that come into contact with the rotor and impeller can be injured. Secure the device against accidental contact. Before working on the system/machine, wait until all parts have come to a standstill. WARNING Rotating device Long hair, dangling items of clothing, jewellery and similar items can become entangled and be pulled into the device. Risk of injury. Item no. 12161-5-9970 ENG Revision 76115 Release 2012-08-18 Page 2 / 9 ebm-papst Mulfingen GmbH & Co. KG Bachmhle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 info1 de.ebmpapst.com www.ebmpapst.com Translation of the original operating instructions