W4D500-GM01-03 ebm papst

W4D500-GM01-03 AC axial fan - HyBlade sickle-shaped blades (S series) with square full nozzle ebm-papst Mulfingen GmbH & Co. KG Bachmhle 2 D-74673 Mulfingen Phone +49 7938 81-0 Fax +49 7938 81-110 info1 de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen Amtsgericht (court of registration) Stuttgart HRA 590344 General partner Elektrobau Mulfingen GmbH Headquarters Mulfingen Amtsgericht (court of registration) Stuttgart HRB 590142 Nominal data Type W4D500-GM01-03 Motor M4D110-GF Phase 3~ 3~ 3~ 3~ 3~ 3~ Nominal voltage VAC 230 230 277 400 400 480 Wiring Y Y Y Frequency Hz 50 60 60 50 60 60 Method of obtaining data ml ml ml ml ml ml Valid for approval/standard CE CE CE CE CE CE -1 Speed (rpm) min 1350 1510 1590 1350 1510 1590 Power consumption W 690 950 1050 690 950 1050 Current draw A 2.34 2.77 2.72 1.35 1.6 1.57 Max. back pressure Pa 155 145 160 155 145 160 Max. back pressure inH2O 0.62 0.58 0.64 0.62 0.58 0.64 Min. ambient temperature C -40 -40 -40 -40 -40 -40 Max. ambient temperature C 65 60 60 65 60 60 Starting current A 10.6 9.7 12.1 6.1 5.6 7.0 ml = Max. load me = Max. efficiency fa = Free air cs = Customer specification ce = Customer equipment Subject to change Data according to ErP Directive Actual Req. 2015 01 Overall efficiency % 33.3 32.5 09 Power consumption P kW 0.66 es e 02 Measurement category A 09 Air flow q m/h 5985 v 03 Efficiency category Static 09 Pressure increase p Pa 134 fs -1 04 Efficiency grade N 40.8 40 10 Speed (rpm) n min 1355 * 05 Variable speed drive No 11 Specific ratio 1.00 * Data obtained at optimum efficiency level. Specific ratio = 1 + p / 100 000 Pa LU-110665 fs The ErP data is determined using a motor-impeller combination in a standardized measurement setup. Item no. 12024-5-9980 ENU Change 90169 Approved 2016-08-16 Page 1 / 6 ebm-papst Mulfingen GmbH & Co. KG Bachmhle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 info1 de.ebmpapst.com www.ebmpapst.comW4D500-GM01-03 AC axial fan - HyBlade sickle-shaped blades (S series) with square full nozzle Technical description Weight 16.8 kg Fan size 500 mm Rotor surface Painted black Terminal box material PC/ABS plastic Blade material Press-fitted sheet steel blank, sprayed with PP plastic Fan housing material Sheet steel, pre-galvanized and coated with black plastic Guard grille material Steel, coated with black plastic (RAL 9005) Number of blades 5 Airflow direction Direction of rotation Counterclockwise, viewed toward rotor Degree of protection IP54 Insulation class Moisture (F) / Environmental (H) F4-1 protection class Max. permitted ambient temp. + 80 C for motor (transport/storage) Min. permitted ambient temp. for - 40 C motor (transport/storage) Installation position Shaft horizontal or rotor on bottom rotor on top on request Condensation drainage holes On rotor side Mode S1 Motor bearing Ball bearing Touch current according to IEC <= 3.5 mA 60990 (measuring circuit Fig. 4, TN system) Electrical hookup Via terminal box Motor protection Thermal overload protector (TOP) with basic insulation With cable Axial Protection class I (with customer connection of protective earth) Conformity with standards EN 61800-5-1 CE Approval CSA C22.2 No. 100 VDE EAC UL 1004-1 Item no. 12024-5-9980 ENU Change 90169 Approved 2016-08-16 Page 2 / 6 ebm-papst Mulfingen GmbH & Co. KG Bachmhle 2 D-74673 Mulfingen Phone +49 (0) 7938 81-0 Fax +49 (0) 7938 81-110 info1 de.ebmpapst.com www.ebmpapst.com