M-V34EV011
Data Sheet
Evaluation Breakout Board for EPSON IMU
OVERVIEW
This Evaluation Breakout Board is designed to convert the 0.4mm pitch connector of the Epson IMU to a
2.54mm pitch connector. The Evaluation Breakout Board simplifies the initial evaluation and rapid testing of the
Epson IMU products.
OUTLINE DIMENSIONS
2pin 20pin
19pin
1pin
Fig1. Board Outline Dimensions (millimeters)
PIN FUNCTION
Table1. Though-hole Pinout Descriptions
*1
Pin No. Mnemonic Type Description
*2
2 SDI I SPI Data Input
*2
4 SCLK I SPI Serial Clock
*2
6 SDO O SPI Data Output
*2
8 /CS I SPI Chip Select (10k Pull-Up recommended)
7 - N/A Pull-Up10
9,11,19 - N/A DoNotConnect
*2
10 SIN I UART Data Input
*2
12 SOUT O UART Data Output
14 DRDY I/O DataReady
GPIO1 General Purpose I/O1
16 EXT I/O External Trigger Sync or External Counter Reset
GPIO2 General Purpose I/O2
*3
18 /RST I Reset
15,17 VCC S Power Supply 3.3V
1,3,5,13,20 GND S Ground
*1) Pin Type I: Input, O: Output, I/O: Input/Output, S: Supply, N/A: Not Applicable
*2) Connect either SPI or UART but not both. Connecting both SPI and UART at the same time may result in
malfunction of the device. Regarding unused pin, please connect /CS pin to VCC and all other unused input pins
to GROUND.
*3) If the /RST pin is not used, keep the pin at High (VCC) voltage level.
Note) All input pins have weak pull up resistors inside the IMU.
M-V34EV011
SUPPORTED DEVICES
Table2. Supported Devices
Evaluation Breakout Board Supported IMU
M-V34EV011 M-V340PD
PRODUCT NUMBER AND ORDER INFORMATION
CAUTION
Please order using the following number.
Order Number Product Number Comment
E92E603011 M-V34EV011 Evaluation Breakout Board
CAUTION
Evaluation Board/Kit and Development Tool Important Notice
1. This evaluation board/kit or development tool is designed for engineering evaluation, demonstration, or development purposes only.
Do not use it for any other purposes. The conformance test for this product in accordance with European EMC regulations and United
States FCC regulations has not been conducted.
2. This evaluation board/kit or development tool is intended for use by electronics engineers and is not a consumer product. Malfunction
by the electrical noise may result from usage depending on your environment. The user should ensure it is used in a safe and proper
manner.
3. Seiko Epson does not assume any responsibility or liability of any kind from damage and/or fire caused by the use of this evaluation
board/kit or development tool. The user should cease using this evaluation board/kit or development tool if any abnormal issue occurs
even during proper and safe usage.
4. When disposing of this evaluation board/kit or development tool, discard in accordance with domestic law concerning disposal.
5. The parts used for this evaluation board/kit or development tool may be changed without notice.
6. Do not allow heaters, human body or metal parts to contact the non-insulated parts of this evaluation board/kit or development tool.
7. Do not allow the human body or metal parts to contact any openings of this evaluation board/kit or development tool.
8. Do not allow excessive stress on mounted components, board wiring, and electric wire of this evaluation board/kit or development tool.
9. When exporting the products or technology described in this material, the user should comply with the applicable export control laws
and regulations and follow the procedures required by such laws and regulations. Do not use, resell, export and/or otherwise disclose
of these products (and any technical information, if any) for the development and/or manufacture of weapons of mass destruction or
other military purposes.
NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson.
Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind
arising out of any inaccuracies contained in this material and, further, there is no representation that this material is applicable to products
requiring high level reliability, such as, medical products. Moreover, no license to any intellectual property rights is granted by implication
or otherwise, and there is no representation or warranty that anything made in accordance with this material will be free from any patent or
copyright infringement of a third party. Keep this manual at hand to answer any questions you have about this product during use.
All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective companies.
Seiko Epson Corporation 2018, All rights reserved.
MSM BUSINESS PROJECT
281, Fujimi, Fujimi-cho, Nagano 399-0293, JAPAN
Phone: +81-266-61-0614 FAX: +81-266-61-2045
First issue June, 2016 in Japan
Rev.20180314
Seiko Epson Corporation 2