Portable ISP Programmer for Field-Service and Production applications The FS2009USB programmer being used in standalone mode The FS2009USB is a portable ISP programmer designed for field-service and production programming applications. The programmer is FIELD-SERVICE capable of operating in Standalone Mode (without PC) allowing an operator to select from 1 of 64 Standalone Programming Projects using the PRODUCTION PROGRAMMING display and keypad. A single Autoprogram key is then used to repetitively program the selected project. TARGET / USB POWERED Portable In-System (ISP) Programmer Ideal for Field-service or low-volume Production programming FIRMWARE UPGRADEABLE Supports In-system Programming (ISP) of many different programmable microcontrollers and serial memory devices Supports programming via SPI, JTAG, I2C and UART interfaces Supports Standalone operation - no PC required after programmer has been configured Low power consumption allows the programmer to be powered from most Target Systems (no external supply required) High-speed USB connection to PC Backwards compatible with FS2003 and FS2009 programmers Power supply is reverse-polarity protected Programming Interfaces: Fixed +12V Target VPP voltage generator Supports most ISP hardware interfaces / for ATtiny HV devices protocols including JTAG, SPI, I2C, ATtiny AVR HV mode, 8051 UART Bootloader Very fast programming speeds suitable for J3 Atmel J6 Equinox 6-way Header 10-way Header Pin 1 high-throughput production environments Robust I/O driver stage Individually configurable programmer I/O pins Pin 1 Supports programming of target ICs Pin 1 Pin 1 between 3.0 and 5.0V. Programmable frequency generator output J8 JTAG J7 Atmel Programmer 10-way Header 10-way Header on SCK2 pin - supports external clocking of ISP Connectors AVR microcontrollers to speed up programming Target ISP connectors / headers: Control methods: Microcontroller Most popular ISP connectors are catered for PC control via on-board USB port ARM standard 20-pin and 10-pin JTAG User Standalone keypad / display operation Target connectors requires a special ARM JTAG System Standalone Mode: cable (available separately) ISP Cable Supports loading of up to 64 x Atmel Header Equinox Header Software (as standard): Standalone Programming (6-way) (10-way) EQTools - creates Standalone Projects into the programmer JTAG Header Atmel Header (10-way) (10-way) Programming Projects memory (4 Mbytes capacity) EDS - Development Mode for testing under Project selection via the keypad PC control and display (no PC required) Upload Wizard - uploads projects to the Single-button auto-program programmer operation allows repetitive execution of the selected Typical applications: project Field-service programming - supports Programmer up to 64 different customer firmware / product versions Low to medium volume production USB Cable programming Power Supply Unit (PSU) Device support: Atmel AVR (not XMEGA or ATtiny TPI) ARM FLASH microcontrollers - PC ARM7TDMI , Cortex M3, Cortex M4 Selected 8051 FLASH microcontrollers Typical programmer connection to PC and Serial EEPROMs (I2C) Target System (DUT) Zensys Z-wave devices Power supply: The programmer can be powered from: - User Target System (3.1 - 5.0V 60mA) - External power supply via jack socket (6.0 - 12.0V 60mA) System Contents: - PC USB Port (PC dependent) The picture shows the typical contents of the - External USB Power Pack (+5V only) USB port External DC FS2009USB programming kit. Programmer can supply +5V regulated (J5) Power Supply Input (CON1) power to the Target system when it is The programmer is also available separately powered from an external supply without any power supply or cables. Bottom panel connections Ordering information: There are three different versions of the FS2009USB programmer each with different device support... FS2009USB(UN) - Programmer supporting AVR microcontrollers via the SPI interface, 8051, Zensys devices FS2009USB (AVR-JTAG) - Programmer supporting AVR microcontrollers via the JTAG interface only FS2009USB(ARM) - Programmer supporting ARM microcontrollers It is possible to purchase separate Device Library upgrades for any version of the programmer. Equinox Technologies reserves the right to change any information contained within this leaflet without prior notice. E&OE Equinox House, 217 Church Street Westhoughton, Bolton, Lancashire BL5 3SW United Kingdom Telephone: +44 (0)1942 841975 : Fax: +44 (0)1942 844181 : Email: info equinox-tech.com : Web: www.equinox-tech.com SCK2 0V Target Vcc