8845A/8846A Digital Multimeters accessory guide Technical Data Introduction The 8845A/8846A Digital Multimeters are complemented by a comprehensive range of accessories, all of which are designed to help you get the most from your multimeter. This data sheet explains in more detail the makeup of key acces- sories and offers technical specifications where required. Test leads, probes, and probe tips TL71 Premium Test Lead Set TL80A Basic Electronic DMM Test Set Included with 8845A One pair (red, black) each 1 meter and 8846A long silicone test lead set, alligator clip and probe tip extender One pair (red, black) comfort grip probes Probe tip size: 2 mm with silicone insu- C75 soft carrying case lated, right-angle test CAT II 300 V. UL listed. leads One-year warranty Probe tip size: 2 mm Recommended for V 8845A-TPIT Test Probe IC Tip Set measurements One pair (red and black) CAT IV 600 V, CAT III Snaps onto DMM probes with 1000 V, 10 A rating. UL listed080 in (2 mm) O.D. Tips One-year warranty Designed to IEC 1010 standard Pin tip jack at the adapter end TL910 Precision Electronic Probe Set is recessed for added insulation Very small 1 mm protection tips to access hard- Adapter allows easy access to to-reach test points leads of through-hole ICs Probe tip length up Insulation at the tip fits between to 100 mm, test lead leads to prevent accidental shorting length: 1 m Included : 3 sets of Specifications spring loaded gold Materials Tip:Stainless steel, nickel plated tips and 2 sets of Body:P olypropylene, fire retardant, UL94V -2 rated stainless steel tips Color One red, one black CAT IV 600 V, CAT III Safety IEC 1010-2-031, CategoryI I, P2 compliant 1000 V, 3 A rating Operating 300V rms/dc One-year warranty voltage Current 3A Test leads, probes, and probe tips cont. 8845A-EFPT Fine Point Extended Test Probe 884X-Short 4-wire short Adapter Set 4-terminal shorting bar One pair (red 4 mm banana terminals and black) sized and orientated to Snaps onto short DMM input source and DMM probes sense terminals with .080 in Used to null out front end (2 mm) O.D. offsets or as required by the Tips calibration procedure Designed to IEC 1010 standard 884x-RTD 100 Ohm RTD Temperature Probe Adapter allows access to hard-to-reach test Manufactured using a points coil suspension element Tips are insulated to the point to prevent short- design for increased ing of adjacent components shock and vibration resistance Specifications Mineral-insulated Materials Tip:Stainless steel Tip insulation: sheath with a minimum Kynar Body: Polypropylene, fire bend radius of 19 mm retardant,U L94 V-2 rated (3/4 in) for flexibility Color One red, oneblack and durability Safety IEC1 010-2-031, CategoryI I, P2 compliant Operating 300V rms/dc Specifications voltage Resistance Nominal 100 Current 3A Temperature coefficient 0.00385 / C nominal Temperaturerange -200 C to 300 C(transition and cable TL2X4W-PTII 2X4 Wire Ohms Test Lead temperature: 0C to 150C) Perform 4- Driftrate +0. 13 Cat 0 C after 1000hours at wire measure- 300 C ments with Sheath material 316 stainless steel only two test Leads Teflon -insulated, nickel-plated stranded leads copper, 22A WG Two conduc- Termination 4-wirebanana tors per lead (one source Time constant Four seconds maximum for 63.2 % and one response to step change in watermov ing measure) at 3 fps Excellent resolution and accuracy Bendingradius 19mm (3/4 in) except for50 mm (2 in) areaof sheath near tip Specifications Calibration Includesmanufacturers N IST-traceable Maximumvoltage b etweentest lead and ground: calibrationand table with R vs.T values 1000V in1 Cincrements from -196 C to300 C . Maximum transientover voltage andinput voltage Callendar van Dusen c oefficients combined: 1000 V included Maximum current: 500 mA Immersion Atleast 1 00 mm (4in) recommended Temperature Operating: 0 to 55C < 90% Accuracy (includes cali - 0.050 C at-1 96 C relativehumidity brationunc ertaintyand 0.050 C at0 C Storage: -40 Cto 1 70C short-termstability) 0.051 C at 200C Altitude 2000m 0.055 C at 300 C Safety Compliesw ithE N/IED6 1010-031 Size 9 in L x3/ 16in diameter and CAN/CSA C22.2 No.6 1010-1- Marking Each RTD is marked withthe Fluke name 04 for Measurement Category1 andpart number 1000 V