Symbols International electrical symbols used on the Product and in this document are explained below. Symbol Description BC190/830 WARNING - RISK OF DANGER. Consult user documentation. Universal Mains-Power Adapter WARNING. HAZARDOUS VOLTAGE. Risk of electric shock. DC (Direct Current) Instruction Sheet Double Insulated Introduction Conforms to European Union directives. The BC190/830 is a universal mains-power adapter (the Adapter or Product) for measurement, control, and laboratory equipment. The Energy Efficiency Level VI VI Adapter is intended for operating and charging the Fluke 190-Series ScopeMeter Test Tool (test tool). The Adapter is based on the switched- This product complies with the WEEE Directive marking mode concept for high efficiency, low stand-by power consumption, and requirements. The affixed label indicates that you must not discard complies with level-VI requirements. It operates in a wide range of input this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the voltages from 100 Vac up to 240 Vac nominal. WEEE Directive Annex I, this product is classed as category 9 A universal set of mains cords is included to make the Adapter suitable Monitoring and Control Instrumentation product. Do not dispose of this product as unsorted municipal waste. for most types of mains outlet. Conforms to relevant South Korean EMC Standards. Certified by ETL Intertek to North American safety standards. LIMITED WARRANTY AND LIMITATION OF LIABILITY This Fluke product will be free from defects in material and workmanship for one year from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Flukes behalf. To obtain service during the warranty period, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product to that Service Center with a description of the problem. THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. How to Contact Fluke FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR To contact Fluke, call one of the following telephone numbers: CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR Technical Support USA: 1-800-44-FLUKE (1-800-443-5853) THEORY. Since some states or countries do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853) liability may not apply to you. Canada: 1-800-36-FLUKE (1-800-363-5853) Europe: +31 402-675-200 Fluke Corporation Fluke Europe B.V Japan: +81-3-6714-3114 P.O. Box 9090 P.O. Box 1186 Singapore: +65-6799-5566 Everett, WA 98206-9090 5602 BD Eindhoven U.S.A. The Netherlands Anywhere in the world: +1-425-446-5500 11/99 Or, visit Flukes website at www.fluke.com. To register your product, visit Safety Information Specifications Input A Warning identifies conditions and procedures that are dangerous to the Nominal input voltage ............... 100 Vac to 240 Vac, 10 % user. Input current .............................. 0.35 A at max. load Warning Nominal input frequency ........... 50/60 Hz 10 % To prevent electrical shock, fire, or personal injury: Mains inlet ................................. IEC 60320-1 type C8 Read these instructions carefully before using the Product. Input power, no load.................. <0.1 W ( 115 / 230 Vac) Use the Product only with Fluke test tools that have the type Output number BC190 specified for charge and operation. Output voltage........................... 18 Vdc 5 % Use this Product only as specified. Output current ........................... 0 mA to 840 mA Do not open the Product, it has no user-serviceable parts inside. Output cable length ................... 2 m (6.5 ft) Do not use the Product around explosive gas, vapor, or in damp or Output connector ...................... 5 mm outer diameter, per DIN45232 wet environments. Output polarity........................... Inner contact negative, outer contact positive Use this Product indoors only. Physical characteristics Examine the case before you use the Product. Look for cracks or Dimensions of main unit............ 79 mm x 149 mm x 49 mm missing plastic. Carefully look at the cable jacket and insulation Housing material ....................... Heat resistant ABS around the terminals. Color (housing and cable) ......... Black Use only the mains power cord and connector approved for the Weight ....................................... 0.35 kg voltage and plug configuration in your country and rated for the Ingress Protection ..................... IEC 60529, IP40 Product. Environmental.............................. Replace the mains power cord if the insulation is damaged or if the Operating temperature .............. 0 C to 50 C (32 F to 122 F), up to 90 % rel. insulation shows signs of wear. humidity, no condensation Do not use the Product if it is altered or damaged. Storage temperature ................. -40 C to +70 C, 10 % to 95 % rel. humidity Max. altitude.............................. 2000 m (6562 ft) above sea-level Unpack The Adapter includes these items: Included accessories BC190/830 Switch Mode Power Adapter (main unit) with dc cable Power cord ................................ Universal set of 2-wire cords Universal set of 2-wire mains cords with male and female connector Mains cord length...................... 1.8 m (6 ft), male to female Power plug adapters ................. US-style, UK-style, European, Japanese, At delivery of the Adapter, make sure that the shipment is complete and all Chinese/Australian, Brazilian items are undamaged. Contact your supplier if you see any damage. Safety ............................................ IEC 61010-1, IEC 61010-2-030: CAT IV 600 V, Operation Pollution Degree 2 The power cord connects the Adapter to the mains system. Do not block Electromagnetic access to the power cord and power plug, these must remain accessible to Compatibility (EMC) .................... IEC 61326-1: Industrial Electromagnetic the user at all times. Environment CISPR 11: Group 1, Class A The Adapter is not equipped with a power switch. Disconnect the mains plug from the mains system when not in use. Group 1: Equipment has intentionally generated and/or use conductively coupled radio-frequency energy which is necessary for the internal functioning In case the Adapter is damaged or any damage is suspected, disconnect of the equipment itself. from the mains system and have qualified service personnel inspect the Class A: Equipment is suitable for use in all establishments other than Adapter before reconnecting to the mains system again. domestic and those directly connected to a low voltage power supply network To use: which supplies buildings used for domestic purposes. There may be potential difficulties in ensuring electromagnetic compatibility in other environments, 1. Connect the mains cord to the Adapter. due to conducted and radiated disturbances. 2. Connect the power plug to the mains system. Korea (KCC) ................................ Class A Equipment (Industrial Broadcasting & 3. Connect the dc plug to the test tool. Communication Equipment) For continuous operation and recording with the test tool, keep the power Class A: Equipment meets requirements for industrial electromagnetic wave adapter connected. equipment and the seller or user should take notice of it. This equipment is intended for use in business environments and not to be used in homes. The Adapter operates and charges the test tool from local line voltage. Any power supply connected to the test tool introduces a certain capacitive coupling between the test tool and ground through the power supply circuitry. This capacitive coupling can affect test tool measurements. The Adapter is equipped with dedicated decoupling networks to reduce possible effects of such capacitive coupling during measurements. For an optimal decoupling from ground, especially to make low-level measurements, Fluke recommends that you work in battery-operated mode without any power adapter connected. See the User Manual for the test tool to find complete safety information before making any measurements. Note Always fully charge the test tool battery before storage.