6MBP20XSD060-50 IGBT Modules IGBT MODULE (X series) 600V / 20A / IPM Features Low-side IGBTs are separate emitter type Short circuit protection Temperature sensor output function Under voltage protection Fault signal output function Input interface : TTL (3.3V/5V) Active high logic Applications AC 100 ~ 240V three phase inverter drive for small power AC motor drives (such as compressor motor drive for air conditioner, compressor motor drive for heat pump applications, fan motor drive, ventilator motor drive) Terminal assign and Internal circuit VB( U) Pin No. Pin Name Pin Description 3 NC 36 VB (V ) 3 VB(U) High-side bias voltage for U-phase IGBT driving 5 VB (W ) P 5 VB(V) High-side bias voltage for V-phase IGBT driving 7 3 2 7 VB(W) High-side bias voltage for W-phase IGBT driving IN (H U ) 9 IN(HU) Signal input for high side U-phase 9 IN V B 10 IN(HV) Signal input for high side V-phase Vc c OUT 11 IN(HW) Signal input for high side W-phase U G ND V s 30 12 VCCH High-side control supply 13 COM Common supply ground IN (H V ) 10 IN V B 14 IN(LU) Signal input for low side U-phase Vc c OUT 15 IN(LV) Signal input for low side V-phase V G ND V s 28 16 IN(LW) Signal input for low side W-phase 17 VCCL Low-side control supply IN (H W ) 11 I N V B 18 VFO Fault output V C C H 12 Vcc OUT 19 IS Over current sensing voltage input C OM W 20 COM Common supply ground 13 G ND V s 2 6 21 TEMP Temperature sensor output IN (L U ) 14 U I N 22 N(W) Negative bus voltage input for W-phase U OUT IN (L V ) 15 V 23 N(V) Negative bus voltage input for V-phase I N N ( U) 2 4 IN (L W) 24 N(U) Negative bus voltage input for U-phase 16 W I N 26 W Motor W-phase output V V C CL OUT 17 Vc c 28 V Motor V-phase output V FO N ( V) 18 Fo 2 3 30 U Motor U-phase output IS 32 P Positive bus voltage input 19 IS W OUT 36 NC No Connection C OM 20 G ND N (W ) TE MP 22 21 TE M P 1695b 1 MARCH 20166MBP20XSD060-50 IGBT Modules Absolute Maximum Ratings at Tj=25C, VCC=15V (unless otherwise specified) Items Symbol Characteristics Unit Remarks DC Bus Voltage VDC 450 V Note *1 Bus Voltage (Surge) VDC(Surge) 500 V Note *1 Collector-Emitter Voltage VCES 600 V Collector Current IC 25 20 A Note *2 VCC 15V, VB(*)15V 40 A Note *2, *3, *4 Peak Collector Current ICP 25 VCC 13V, VB(*)13V 30 A Note *2, *3, *4 Diode Forward current IF 25 20 A Note *2 Peak Diode Forward current IFP 25 40 A Note *2 Collector Power Dissipation PD IGBT 41.0 W per single IGBT TC=25C FWD Power Dissipation PD FWD 27.8 W per single FWD TC=25C Junction Temperature Tj 150 C Operating Junction Temperature TjOP -40 ~ +150 C High-side Supply Voltage VCCH -0.5 ~ 20 V Applied between VCCH-COM Low-side Supply Voltage VCCL -0.5 ~ 20 V Applied between VCCL-COM VVB(U)-COM Applied between High-side Bias Absolute Voltage VVB(V)-COM -0.5 ~ 620 V VB(U)-COM, VB(V)-COM, VVB(W)-COM VB(W)-COM VB(U) High-side Bias Voltage for VB(V) -0.5 ~ 20 V Note *4 IGBT gate driving VB(W) VU Applied between High-side Bias offset Voltage VV -5 ~ 600 V U-COM, V-COM, W-COM VW Note *5 -0.5 ~ VCCH+0.5 Input Signal Voltage VIN V Note *6 -0.5 ~ VCCL+0.5 Input Signal Current IIN 3 mA sink current Fault Signal Voltage VFO -0.5 ~ VCCL+0.5 V Applied between VFO-COM Fault Signal Current IFO 1 mA sink current Over Current sensing Input Voltage VIS -0.5 ~ VCCL+0.5 V Applied between IS-COM Junction Temperature Tj 150 C Operating Case Temperature TC -40 ~ +125 C See Fig.1-1 Storage Temperature Tstg -40 ~ +125 C Isolation Voltage Viso AC 1500 Vrms Sine wave,60Hz t=1min , Note *7 Note *1 : Applied between P-N(U),P-N(V),P-N(W) Note *2 : Pulse width and duty were limited by Tjmax. Note *3 : VCC is applied between VCCH-COM,VCCL-COM. Note *4 : VB(*) is applied between VB(U)-U,VB(V)-V, VB(W)-W. Note *5 : Over 13.0V applied between VB(U)-U,VB(V)-V, VB(W)-W. This IPM module might make incorrect response if the high-side bias offset voltage is less than -5V. Note *6 : Applied between IN(HU)-COM,IN(HV)-COM,IN(HW)-COM,IN(LU)-COM,IN(LV)-COM,IN(LW)-COM. Note *7 : Applied between shorted all terminal and IMS (Insulated Metal Substrate). 1695b 2 3 MARCH 2016 Control circuit block Inverter block