NEW ESP Cat-5 & Cat-6 Series Installation Connect in series with the network cable, either: a) near to where it enters or leaves the building, or b) as it enters the network hub, or c) close to the equipment being protected This should be close to the systems earth star point (to enable a good connection to earth). DIRTY CLEAN ELECTRONICSYSTEMSPROTECTION Plug-in Lightning Barrier Wilford Road, Nottingham, NG2 1EB, UK Combined Category D, C, B tested protector (to BS EN 61643) suitable to protect twisted pair Ethernet networks, including From To line equipment Power over Ethernet (PoE), with RJ45 connections. For use at Earth boundaries up to LPZ 0 to protect against flashover (typically the Plug-in series connection B service entrance location) through to LPZ 3 to protect sensitive electronic equipment. Features and benefits Suitable for systems signalling on up to eight wires of either shielded or unshielded twisted pair cable Very low let-through voltage (enhanced protection to BS EN 62305) between all lines - Full Mode protection Full mode design capable of handling partial lightning currents as well as allowing continual operation of protected equipment Repeated protection in lightning intense environments Unlike some competing devices, the ethernet SPDs provide effective A Furse ESP Cat-5e/Gb protecting a hub from transient overvoltages on a network protection without impairing the systems normal operation connection with another building Low capacitance circuitry prevents the start-up signal degradation associated with other types of network protector Low in-line resistance minimises unnecessary reductions in signal Technical note strength to maximise signalling distance The interfaces used in Ethernet Sturdy ABS housing with convenient holes for flat mounting, or networks incorporate an vertically via TS35 Top Hat DIN rail isolation transformer which gives these systems an inbuilt Substantial earth connection to enable effective earthing immunity to transients Supplied with short (50 cm) Cat-5e UTP or Cat-6 STP cable to enable between line and earth of neat installation 1,500 Volts or more. Application Accessories Use these protectors on network cables that travel between buildings to prevent damage to equipment, e.g. computers, servers, repeaters and hubs. ESP CAT5e/UTP-1 Suitable for computer networks up to Cat-6 cabling. 1 metre cable with unshielded To protect up to 100baseT and up to 1000baseT networks with RJ45 connections Cat-5/Cat-5e cabling use ESP Cat-5e and ESP Cat-5e/Gb respectively ESP CAT6/STP-1 To protect up to 10GbaseT networks with Cat-6 cabling use ESP Cat-6 1 metre screened cable with shielded RJ45 connections To protect up to 100baseT, 1000baseT and 10GbaseT Power over Ethernet (PoE) networks use ESP Cat-5e/PoE, ESP Cat-5e/Gb/PoE and ESP Cat-6/PoE respectively For further application information, see separate Application Note AN004 (contact us for a copy). Furse, Wilford Road, Nottingham, NG2 1EB Tel: +44 (0)115 964 3700 Email: enquiry furse.com Web: www.furse.comNEW ESP Cat-5 & Cat-6 Series Technical specification IMPROVED IMPROVED NEW NEW NEW Electrical specification ESP Cat-5e ESP Cat-5e/PoE ESP Cat-5e/Gb ESP Cat-5e/Gb/PoE ESP Cat-6 ESP Cat-6/PoE 2 Maximum working - data 5 V 5 V 5 V 5 V 5 V 5 V 1 3 voltage Uc - power - 58 V - 58 V - 58 V 4 4 4 Current rating 300 mA 400 mA 300 mA 400 mA 300 mA 400 mA 2 In-line resistance - data 1 1 1 1 1 1 3 (per line 10%) - power - 4.4 - - - - Maximum data rate 100 Mbps 100 Mbps 1000 Mbps 1000 Mbps 1000 Mbps 1000 Mbps Networking standards 10/100baseT 10/100baseT 10/100/1000baseT 10/100/1000baseT 10/100/1000/ 10/100/1000/ 10GbaseT 10GbaseT TIA Cat-5e TIA Cat-5/PoE TIA Cat-5e TIA Cat-5e TIA Cat-6 TIA Cat-6 IEEE 802.3i IEEE 802.3i IEEE 802.3i IEEE 802.3i IEEE 802.3i IEEE 802.3i IEEE 802.3u IEEE 802.3u IEEE 802.3u IEEE 802.3u IEEE 802.3u IEEE 802.3u IEEE 802.3af IEEE 802.3ab IEEE 802.3ab IEEE 802.3ab IEEE 802.3ab IEEE 802.3af IEEE 802.3an IEEE 802.3an IEEE 802.3af Transient specification ESP Cat-5e ESP Cat-5e/PoE ESP Cat-5e/Gb ESP Cat-5e/Gb/PoE ESP Cat-6 ESP Cat-6/PoE 5 Let-through voltage (all conductors) Up 8 8 8 C2 test 4 kV 1.2/50 s, - line to line 120 V 120 V/88 V 120 V 120 V/86 V 120 V 120 V/86 V 6 2 kA 8/20 s to - line to earth 700 V 700 V 700 V 700 V 700 V 700 V BS EN/EN/IEC 61643-21 8 8 8 C1 test 1 kV, 1.2/50 s, - line to line 74 V 74 V/63 V 74 V 74 V/73.5 V 74 V 74 V/73.5 V 6 0.5 kA 8/20 s to - line to earth 600 V 600 V 600 V 600 V 600 V 600 V BS EN/EN/IEC 61643-21 8 8 8 B2 test 4 kV 10/700 s to - line to line 21 V 21 V/65 V 21 V 21 V/65 V 21 V 21 V/65 V 6 BS EN/EN/IEC 61643-21 - line to earth 550 V 550 V 550 V 550 V 550 V 550 V 7 8 8 8 5 kV, 10/700 s - line to line 25 V 25 V/80 V 25 V 25 V/65.8 V 25 V 25 V/65.8 V 6 - line to earth 600 V 600 V 600 V 600 V 600 V 600 V 9 Maximum surge current D1 test 10/350 s to BS EN/EN/IEC 61643-21 1 kA 8/20 s to ITU-T K.45:2003, 10 kA IEEE C62.41.2:2002 Mechanical specification ESP Cat-5e, ESP Cat-5e/PoE, ESP Cat-5e/Gb, ESP Cat-5e/Gb/PoE ESP Cat-6, ESP Cat-6/PoE Temperature range -40 to +80 C -40 to +80 C Connection type RJ45 sockets RJ45 sockets Cable (supplied) 0.5 m Cat-5e UTP patch lead 0.5 m Cat-6 STP patch lead Earth connection M4/DIN rail M4/DIN rail Case material ABS UL94 V-0 ABS UL94 V-0 Weight - unit 0.15 kg 0.15 kg Weight - packaged 0.2 kg 0.2 kg Dimensions 1 Maximum working voltage (DC or AC peak) measured at 106 mm 1 mA leakage. 2 Data pairs 1/2 and 3/6 are protected as standard. Pairs 4/5 and 7/8 are also protected on Gigabit (Gb) & Cat-6 barriers. 3 PoE protectors transmit power to IEEE 802.3af. ESP Cat-5e/PoE using Mode A (combined phantom power/data) and Mode B (power on spare pairs 4/5 and 7/8), ESP Cat-5e/Gb/PoE and ESP Cat-6/PoE using Mode A (combined 54 mm 60 mm Depth: 24 mm phantom power/data) only. 4 Based on 15.4 W of transmitted PSE power, to IEEE 802.3af. 49 mm Fixing centres 5 The maximum transient voltage let-through of the protector 49 x 54 mm, throughout the test (10%), line to line & line to earth. Response M3 clearance time <10 ns (on all protected pairs). 6 The interfaces used in Cat-5/5e systems incorporate an isolation transformer that inherently provides an inbuilt immunity to transients between line and earth of 1,500 Volts or more. 7 Test to IEC 61000-4-5:2006, ITU-T (formerly CCITT) K.20, K.21 To protect datacomms systems based on twisted pairs, use the ESP D, E or H Series. Local and K.45,Telcordia GR-1089-CORE, Issue 2:2002, protection for networked equipment is also available. For protection of legacy coaxial Ethernet ANSI TIA/EIA/IS-968-A:2002 (formerly FCC Part 68). 8 The first number is for the data pair, with the second number for networks, please contact us for details of our ESP ThinNet and ESP ThickNet protectors. the power pair. 9 The installation and connectors external to the protector may limit the capability of the protector. Furse, Wilford Road, Nottingham, NG2 1EB Tel: +44 (0)115 964 3700 Email: enquiry furse.com Web: www.furse.com