M85049/112S12KW05-7 Glenair

AS85049 AS85049/112 Straight RFI/EMI Shield-Sock Shrink Boot Adapter with Optional Self-Locking Coupling Nut CONNECTOR DESIGNATOR: Product Series and Shell Size Shield Finish Entry Size Drain Hole (Table I) (Table IV) (Table II) (Omit for None) Specification Sheet MIL-DTL-38999 Series I and II F M85049/112 S 10 T W 03 - 6 D B Braid Length S = Detented, Self-Locking Finish 1 Inch Increments, = Non-Self-Locking (Use Dash) (Table III) 6 Min., 18 Max N = Non-Detented, Self-Locking See Note 9 O-Ring 1.19 (30.2) Max Length A Thread .50 (12.7) Z W B See Note 5 Y Marking Location Optional Single Layer Shield .075 (1.9) Knurl Style Mfr (Ref) Option - Typ .140 (3.56) See Note 8 .130 (3.30) Coupling Nut Adapter Body Dimensions in inches (millimeters) and are subject to change without notice. 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. 1211 AIR WAY GLENDALE, CA 91201-2497 818-247-6000 FAX 818-500-9912 www.glenair.com B-118 E-Mail: sales glenair.comAS85049/112 Straight RFI/EMI Shield-Sock Shrink Boot Adapter with Optional Self-Locking Coupling Nut TABLE I: Shell Size, Entry Size, Thread and Dimensions TABLE II: Entry Size and Dimensions Accessory Series I Series II Allowable A B Max Shell Size Shell Size Shell Size Cable Y Thread Class 2B Diameter Entry W Z Code (Ref) (Ref) Entry Size +.008 (.20) Size .020 (.51) Max -.000 (.00) 08 9 8 7/16-28 UNEF .858 (21.79) 01 10 11 10 9/16-24 UNEF .984 (24.99) 01-03 01 .250 (6.4) .044 (1.12) .560 (14.2) 12 13 12 11/16-24 UNEF 1.157 (29.39) 01-05 02 .312 (7.9) .044 (1.12) .630 (16.0) 14 15 14 13/16-20 UNEF 1.279 (32.49) 03-07 03 .375 (9.5) .044 (1.12) .690 (17.5) B 16 17 16 15/16-20 UNEF 1.406 (35.71) 05-09 04 .438 (11.1) .044 (1.12) .750 (19.1) 18 19 18 1 1/16-18 UNEF 1.516 (38.51) 06-10 05 .500 (12.7) .044 (1.12) .820 (20.8) 20 21 20 1 3/16-18 UNEF 1.642 (41.71) 08-12 06 .562 (14.3) .044 (1.12) .890 (22.6) 22 23 22 1 5/16-18 UNEF 1.768 (44.91) 09-13 07 .625 (15.9) .044 (1.12) .950 (24.1) 24 25 24 1 7/16-18 UNEF 1.889 (47.98) 10-14 08 .688 (17.5) .044 (1.12) 1.020 (25.9) 09 .750 (19.1) .069 (1.75) 1.120 (28.4) 10 .812 (20.6) .069 (1.75) 1.200 (30.5) 11 .875 (22.2) .069 (1.75) 1.270 (32.3) 12 .938 (23.8) .069 (1.75) 1.260 (32.0) 13 1.000 (25.4) .069 (1.75) 1.370 (34.8) 14 1.125 (28.6) .069 (1.75) 1.470 (37.3) Table III: Symbol and Finish Table IV: Symbol and Finish Table V: (Manufacturers Option) Symbol Finish Symbol Finish Material Finish N Electroless Nickel K Nickel Plate Copper Tin Plate Cadmium/Olive Drab over Electroless T Tin Plate Stainless Steel Passivated W Nickel (1000 Hour Salt Spray) X Nickel Flurocarbon Polymer Z Zinc Nickel APPLICATION NOTES 1. Metric equivalents are given for general information only and shall be specified as in Table V. are based on 1.000 inch (25.40 mm). 6. Shrink boot (when required) shall be as specified in AS5258. 2. Dimensions are in inches and apply after plating. Accessory 7. Termination of the accessory shield with harness shield configuration is optional within the specified dimension may be performed with a AS85049/93 shield support ring or envelope. similar split ring accessory types. 3. Adapter length is measured from the bottom of the accessory 8. Three (3) holes equally spaced shall be provided and teeth to the adapter that is covered by the braid, The adapter accommodate .020 (.51) maximum safety wire for the non- surface under the braid shall be ribbed knurled or have a self-locking coupling configuration. surface roughness of .125 R minimum in accordance with ANSI 9. Drain holes will be provided with a.125 (3.2 mm) diameter, B46.1. 4 places equally spaces (optional, see part number 4. Pig tail terminated braid material shall be in accordance with development). O-Ring not required when drain hole option is TableIV. Braid length is defined by Note 1 as shown in the part specified. or indentifying number (PIN). 10. Material/Finish: 5. Termination band configuration is not controlled. Band with Adapter, coupling nut - Al alloy/See Table III buckle may exceed the Z dimension (See Table II) provided Band - See Table V, manufacturers option the band does not interfere with boot attachment, band material Braid - Copper/See Table IV Dimensions in inches (millimeters) and are subject to change without notice. 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. 1211 AIR WAY GLENDALE, CA 91201-2497 818-247-6000 FAX 818-500-9912 www.glenair.com B-119 E-Mail: sales glenair.com AS85049