AS85049 AS85049/141 90 Lipped Miniature Low Profile Heat Shrink Boot Dash Material Number Drain Holes Basic Table II Omit for None Part Number Table I See Note 2 M85049/141 - 19 H C D P B Injection Vent-Ports Adhesive C = Adhesive Lined Omit for None U = No Adhesive Table III P Optional .120 (3.05) Drain Holes (4 Plcs) 90 apart JW and one on Top. See Note 3 J Dia H R See S Recovered Note 2 with Drain Holes T J Dia .120 Ref (3.05) HW H Dia As Supplied Optional .180 (4.57) H Dia U Injection Port H See Note 2 Recovered Optional with Injection-Vent Port .120 (3.05) Vent Port See Note 3 Dimensions in inches (millimeters) and are subject to change without notice. 2013 Glenair, Inc. Mil-Spec Backshells U.S. CAGE Code 06324 Rev. 8.29.14 Printed in U.S.A. GLENAIR, INC. 1211 AIR WAY GLENDALE, CA 91201-2497 818-247-6000 FAX 818-500-9912 www.glenair.com B-154 E-Mail: sales glenair.comAS85049/141 90 Lipped Miniature Low Profile Heat Shrink Boot TABLE I: Dash Number and Dimensions (Continued Below) H Dia H Dia J Dia Min J Dia Max J Dia P R Dash Min Max (As Supplied) (As Supplied) Max (As Recovered) (As Recovered) No. (As Supplied) (As Recovered) Material A, B, H Material G (As Recovered) 10% Ref 19 0.760 (19.3) 0.510 (13.0) 0.250 (6.4) 0.180 (4.6) 0.080 (2.0) 1.750 (44.5) 0.640 (16.3) 20 1.030 (26.2) 0.750 (19.1) 0.300 (7.6) 0.220 (5.6) 0.100 (2.5) 2.650 (67.3) 0.710 (18.0) 21 1.350 (34.3) 1.020 (25.9) 0.380 (9.7) 0.260 (6.6) 0.120 (3.0) 3.200 (81.3) 0.740 (18.8) 22 1.720 (43.7) 1.340 (34.0) 0.450 (11.4) 0.310 (7.9) 0.140 (3.6) 4.550 (115.6) 0.840 (21.3) TABLE I: Dash Number and Dimensions (Continued from Above) B T HW JW S U Dash (As Recovered) (As Recovered) Max (As Recovered) (As Recovered) No. Ref 20% (As Recovered) 10% 10% 19 0.040 (1.0) 0.060 (1.5) 0.050 (1.1) 0.470 (11.90) 0.220 (5.6) 20 0.040 (1.0) 0.070 (1.8) 0.050 (1.1) 0.470 (11.90) 0.330 (8.4) 21 0.040 (1.0) 0.070 (1.8) 0.050 (1.1) 0.470 (11.90) 0.450 (11.4) 22 0.070 (1.8) 0.070 (1.8) 0.050 (1.1) 0.470 (11.90) 0.610 (15.5) TABLE II: Shrink Boot Materials TABLE III: Adhesive Description Material Color Compound Material Description Symbol Adhesive Description Code Code A 2071 Flexible Polyolefin WHITE C Zero Halogen / Hot Melt B 2040 General Purpose Polyolefin RED G 2010 Zero Halogen Polyolefin GREEN H 2025 High Performance Elastomer BLUE APPLICATION NOTES 1. See bag identification for matching boot number, not number on boot. See part number development for full description. 2. Encircled material letter designator located on O.D. approximately mid length along the J end. See part number development for full description. 3. Dimensions applicable for both injection and vent ports. 4. Metric dimensions (mm) are in parentheses. Dimensions in inches (millimeters) and are subject to change without notice. 2013 Glenair, Inc. Mil-Spec Backshells U.S. CAGE Code 06324 Rev. 8.29.14 Printed in U.S.A. GLENAIR, INC. 1211 AIR WAY GLENDALE, CA 91201-2497 818-247-6000 FAX 818-500-9912 www.glenair.com B-155 E-Mail: sales glenair.com AS85049