Other GREENLEE Safety Instructions and Punching Products . Parts List 53 Sizes of Round Punches 12 Sizes of Square Punches 17 Sizes of Rectangular Punches 3 Sizes of D Punches 5 Sizes of Double D Punches 4 Sizes of Key Punches 2 Sizes of Keyway Punches 229, 231, RS232, 234 and 238 Connector Punches 2 Sizes of Round Punches with 4 Notches Read and understand this maerial before oper- ating. Failure to understand how to safely operate Need Special Size Punches the tool could result in an accident causing Call for Details . serious injury or death. This tool should only be operated by qualified personnel. Greenlee Tools, Inc. 999 9626.0 IM 1069 REV 2 10/19 4455 Boeing Drive, Rockford, IL 61109-2988 USA Printed in USA 2019 Greenlee Tools, Inc. A 10 C B Cat. No. 229 231 RS232 234 238 NAED/DCI No. 78-3310- 34436 34437 34420 34429 34444 No. of Pins 9 15 25 37 50 Wt./Lbs. (Kg) 1.4 (0.635) 1.5 (0.680) 2.0 (0.907) 2.0 (0.907) 2.0 (0.907) .787 1.127 1.655 2.296 2.201 A (20.0 mm) (28.6 mm) (42.0 mm) (58.3 mm) (55.9 mm) B .982 1.309 1.853 2.497 2.402 (24.9 mm) (33.3 mm) (47.1 mm) (63.4 mm) (61.0 mm) C .469 .469 .469 .469 .579 (11.9 mm) (11.9 mm) (11.9 mm) (11.9 mm) (14.7 mm) Punch 34441 34442G 344189 34427G 34443 Die Unit 35196 35197 35198 35199 35200 Draw Stud 34421 34421 34421 34421 34421 Square Retaining Nut 04638 04638 04638 04638 04638 Drive Nut 34733G 34733G 34733G 34733G 34733GDSUBMINIATURE PANEL PUNCHES CAPACITY: 22 THROUGH 16 GAUGE MILD STEEL (0.8 mm - 1.5 mm) & 1/8 (3.2 mm) ALUMINUM Make sure you have firm footing and balance when Do not punch enclosures containing or close to operating. live circuits. Electrical shock could result causing Position yourself to avoid any injuries in case of severe injury or death. slippage, breakage or any other loss of control INFORMATION while punching. Lubricate threads and cutting edges before use. OPERATING WITH WRENCH Ball Bearing Drive Nut Apply Moly Lubricant Layout hole location and drill Insert through 7/16 (11.1 Tighten square nut against Draw Here Stud 7/16 (11.1 mm) pilot hole. mm) pilot hole. draw stud. Die Material Punch to be Punched Square Nut Turn drive nut with 1 wrench Align the centering marks on the Dissassemble, shake slug out until punch is through material outside of the die with the center of opening at side of die. lines of the hole. Tighten the ball completely. bearing drive nut. OPERATING WITH QUICK DRAW PUNCH DRIVER 33967 Square Nut 3/8 Draw Stud Draw Adapter Stud Die Quick Draw Punch Driver Spacer Material to Punch Assemble Punch be Punched OPERATING WITH RAM-TYPE HYDRAULIC PUNCH DRIVER Ram Type 33967 Square Nut Hydraulic 3/8 Draw Stud Punch Driver Draw Adapter Stud Die Punch Material to Assemble Punch be Punched