GLS85LS1002E/1004E/1008E/1016E/1032E/1064E Industrial Grade SATA NANDrive EX Series Factsheet 02.000 November 2020 Features Expanded Data Protection Industry Standard Serial ATA (SATA) Host Interface Added data security through user-selectable protection zones SATA 1.5Gb/s, 3Gb/s and 6Gb/s Secure erase / Data sanitization SATA Revision 3.2 20-Byte Serial Number ATA/ATAPI-8 compliant Supports 48-bit address feature set Factory pre-programmed 10-Byte unique ID Native Command Queuing (NCQ) User-programmable 10-Byte ID up to 32 commands Supports SMART and TRIM Commands Performance Robust Built-in ECC Sequential data read: Up to 470 MByte/sec Thermal Throttling Sequential data write: Up to 340 MByte/sec NAND Configuration (measured using 128 KByte transfer size 1 bit per cell (SLC) tested in VDBench on Linux Designed with Greenliants advanced Power Management EnduroSLC Technology 3.3V and 1.0V power supply Ultra High Endurance Power Consumption 250K P/E cycles Active mode: Operating Temperature Range 64GB: Up to 2180mW Industrial: -40C to 85C 32GB: Up to 1800mW BGA package 16GB: Up to 1980mW 14.0 mm x 24.0 mm x 1.40 mm, 145-ball, 8GB: Up to 1540mW 1.0 mm ball pitch, LBJE (LFBGA) 4GB: Up to 1200mW 14.0 mm x 24.0 mm x 1.55 mm, 145-ball, 2GB: Up to 1200mW 1.0 mm ball pitch, LFJE (LBGA) Idle / Standby mode: <355mW (typical) All Devices are RoHS Compliant DevSleep mode: <70mW (typical) Product Description The GLS85LS10xxE Industrial Grade SATA The integrated NAND flash controller with built-in NANDrive EX Series devices (referred to as SATA advanced NAND management firmware NANDrive in this datasheet) are fully integrated solid communicates with the host through the standard state drives. They combine an advanced Greenliant SATA protocol. It does not require any additional or NAND controller and 2, 4, 8, 16, 32, or 64 GBytes of proprietary software such as the Flash File System NAND flash in a multi-chip package. These products (FFS) and Memory Technology Driver (MTD). are ideal for embedded and portable applications that SATA NANDrive is pre-programmed with a 10-Byte require small form factor, ultra-high endurance and unique serial ID and has the option of programming reliable data storage. an additional 10-Byte serial ID for even greater SATA-interface solid state mass storage technology is system security. widely used in industrial PCs, single board computers, SATA NANDrives advanced NAND management servers, networking appliances, HMI and digital technology enhances data reliability and security, signage displays, test and measurement improves endurance and accurately estimates the instrumentation, multi-functional printers, robotics, remaining life of the NAND flash devices. This video equipment and security systems. innovative technology combines robust NAND SATA NANDrive is a single device, solid state drive controller hardware error correction capabilities with (SSD) that provides the functionality and compatibility advanced wear-leveling algorithms and bad block of a complete SATA hard disk drive (HDD) in a 14 mm management to significantly extend the life of the x 24 mm BGA package for easy, space saving product. mounting to a system motherboard. These products SATA NANDrive devices are offered in a 145-ball BGA, surpass traditional storage in their small size, security, 1 mm ball pitch package. reliability, ruggedness and low power consumption. These specifications are subject to change without notice. 11/23/2020 2020 Greenliant 1 S71469-01 GLS85LS1002E/1004E/1008E/1016E/1032E/1064E Industrial Grade SATA NANDrive EX Series Factsheet 02.000 November 2020 1.0 GENERAL DESCRIPTION Each SATA NANDrive contains an integrated SATA NAND flash memory controller and discrete NAND flash die in a BGA package. Refer to Figure 2-1 for the SATA NANDrive block diagram. 1.1.6 Serial Communication Interface (SCI) 1.1 Optimized SATA NANDrive The Serial Communication Interface (SCI) is The heart of SATA NANDrive is the SATA NAND designed for error reporting. During the product flash memory controller which translates standard development stage, it is recommended to provide SATA signals into flash media data and control the SCI port on the PCB to aid in design validation. signals. The following components contribute to 1.1.7 Multi-tasking Interface SATA NANDrives operation. The multi-tasking interface enables fast, sequential 1.1.1 Microcontroller Unit (MCU) write performance by allowing concurrent Read, The MCU translates SATA commands into data and Program and Erase operations to multiple flash control signals required for flash media operation. media. 1.1.2 Internal Direct Memory Access (DMA) 1.2 EnduroSLC Technology SATA NANDrive uses internal DMA allowing instant data transfer from/to buffer to/from flash media. This EnduroSLC is a proprietary 3D NAND implementation eliminates microcontroller overhead management technology developed by Greenliant associated with the traditional, firmware-based for high reliability applications requiring ultra-high approach, thereby increasing the data transfer rate. endurance and superior data retention. Using 1-bit- per-cell (SLC) NAND configuration, EnduroSLC 1.1.3 Power Management Unit (PMU) enabled SSDs are ideal for write-intensive The PMU controls the power consumption of SATA applications used in extreme temperature, high NANDrive. The PMU dramatically reduces the power stress environments. EnduroSLC enabled solid state consumption of SATA NANDrive by putting the part drives offer a high reliability flash storage solution of the circuitry that is not in operation into sleep with ultra-high write endurance that exceeds mode. capabilities of legacy, planar SLC NAND based The Flash File System handles inadvertent power products. interrupts and has auto-recovery capability to ensure 1.3 SMT Reflow Consideration SATA NANDrive firmware integrity. For regular power management, the host must send a Preprogrammed NAND devices have temperature STANDBY IMMEDIATE (E0h), IDLE IMMEDIATE limits due to data retention. The EnduroSLC SATA (E1h), STANDBY (E2h) or IDLE (E3h) command NANDrive family can withstand multiple passes of and wait for the command-ready before powering SMT high temperature process without losing data. down SATA NANDrive. Using Greenliants recommended reflow profile 1.1.4 Embedded Flash File System during production will help prevent damage to the device and ensure better retention of any The embedded flash file system is an integral part of preprogrammed data through the surface-mount SATA NANDrive. It contains MCU firmware that soldering process. See the relevant datasheet performs the following tasks: section describing the recommended reflow 1. Translates host side signals into flash media temperature limits. writes and reads 2. Provides flash media wear leveling to spread 1.4 Advanced NAND Management the flash writes across all memory address SATA NANDrives integrated controller uses space to increase the longevity of flash media advanced wear-leveling algorithms to substantially 3. Keeps track of data file structures increase the longevity of NAND flash media. Wear 4. Manages system security for the selected caused by data writes is evenly distributed across all protection zones or select blocks in the device to prevent hot spots 1.1.5 Error Correction Code (ECC) in locations that are programmed and erased The ECC technology uses advanced algorithms to extensively. This effective wear-leveling technique detect and correct errors, ensuring data integrity and results in optimized device endurance, enhanced extending the SSD lifespan. data retention and higher reliability required by long- life applications. These specifications are subject to change without notice. 11/23/2020 2020 Greenliant 2 S71469-01