Directory chapter 01 DIN Signal (to 2 A) Types B, 2B, C, 2C, M, Q, 2Q, R, R (HE 11), 2R Page Technical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01.10 Type B connectors . . . . . . . . . . . . . . . . . . . 01.11 Type 2B connectors . . . . . . . . . . . . . . . . . . 01.16 Type C connectors . . . . . . . . . . . . . . . . . . . 01.18 Pin shroud type C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01.24 Application examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01.25 Type 2C connectors . . . . . . . . . . . . . . . . . . 01.26 Type M connectors . . . . . . . . . . . . . . . . . . . 01.28 Special contacts type M . . . . . . . . . . . . . . . 01.30 Type M-flat connectors . . . . . . . . . . . . . . . . 01.32 Type R connectors . . . . . . . . . . . . . . . . . . . 01.34 Type R (HE 11) connectors . . . . . . . . . . . . . 01.36 Type Q, 2Q and 2R connectors . . . . . . . . . . 01.38 Coding systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01.42 01 . 01 Types B, 2B, C, 2C, M, Technical characteristics Q, 2Q, R, R (HE 11), 2R Number of contacts 16-96 Current carrying capacity The current carrying capacity is limited by maximum temperature of Contact spacing (mm) 2.54 materials for inserts and contacts including terminals. The current capacity curve is valid for continuous, non interrupted current loaded Working current 2 A max. contacts of connectors when simultaneous power on all contacts is see current carrying 1 A with insulation displacement given, without exceeding the maximum temperature. capacity chart 40 A max. type M Control and test procedures according to DIN IEC 60 512 Clearance 1.2 mm Creepage 1.2 mm Working voltage The working voltage also depends according to the safety regulations on the clearance and creepage of the equipment dimensions of the pcb itself, Explanations see chapter 00 and the associated wiring Test voltage U 1 kV r.m.s. Contact resistance 15 m for wire wrap connection 20 m including crimp connection 12 Insulation resistance 10 Temperature range 55 C + 125 C The higher temperature limit includes the local ambient and heating effects of the contacts under load Ambient temperature Degree of protection for crimp terminal IP 20 according to DIN 40 050 Electrical termination Pin shroud for female connectors Male connector Solder pins for pcb connections with 0.6 x 0.6 mm pins 1.0 0.1 mm according to IEC 60 326-3 A secure interfacing system for signals from the rear of 19 racks For pcb connection to connectors with wrap posts 0.6 x 0.6 mm is possible with the 0.8 + 0.3 mm on request use of a pin shroud. wrap posts 0.6 x 0.6 mm diagonal 0.79-0.86 mm The pin shroud protects the wrap posts on the rear side of the rack Female connector wrap posts 0.6 x 0.6 mm and can be screwed to the printed circuit board. diagonal 0.79-0.86 mm Solder pins for pcb connections After assembly the rear ends of the wire wrap posts become the 1.0 0.1 mm mating areas of the type C male connector. according to IEC 60 326-3 For pcb connection This system can now accept: 0.8 + 0.3 mm on request Crimp terminal 0.09-0.5 mm female connectors type C Insulation displacement female connectors type R connection AWG 28/7 The locking levers provide security for the mated connectors. Fast and simple disconnection is possible. Insertion and withdrawal force 16way 15 N 32way 30 N 48way 45 N 64way 60 N 96way 90 N Materials Fitting and removing crimp contacts Mouldings Thermoplastic resin, see technical characteristics chapter 02 glass-fibre filled, UL 94-V0 Contacts Copper alloy Contact surface Contact zone Selectively plated according to 1) performance level 1) Explanation performance levels see chapter 00 01 . Mating conditions see chapter 00 10 Working current