Technical Data Sheet LOCTITE 5926 November -2004 PRODUCT DESCRIPTION GENERAL INFORMATION LOCTITE 5926 provides the following product This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as characteristics: a sealant for chlorine or other strong oxidizing materials. Technology Silicone Chemical Type Acetoxy silicone For safe handling information on this product, consult the Appearance (uncured) Blue paste Material Safety Data Sheet (MSDS). Components One component - requires no mixing NOTE: The curing process can cause corrosion to some Cure Room temperature vulcanizing (RTV) surfaces. Application Gasketing Flexibility Enhances load bearing & shock Directions for use absorbing characteristics ofthe bond 1. For best performance bond surfaces should be clean and area. free from grease . Specific Application Gasket replacement or Gasket 2. Moisture curing begins immediately after the product is dressing exposed to the atmosphere, therefore parts to be assembled should be mated within a few minutes after the LOCTITE 5926 cures on exposure to moisture in the air to product is dispensed . form a tough, flexible, silicone rubber gasket. This product 3. The bond should be allowed to cure (e.g.seven days), resists aging, weathering and thermal cycling without before subjecting to heavy service loads . hardening, shrinking or cracking . Typical applications include 4. Excess material can be easily wiped away with non-polar valve covers, timing gear covers, differential covers, oil pans, solvents. transmission pans, water pumps, and thermostat housings . This product is typically used in applications with an operating NOTE: LOCTITE 5926 is not recommended for use range of -54C to 204 C . as a cylinder head gasket or head gasket sealant . TYPICAL PROPERTIES OF UNCURED MATERIAL Not for product specifications Extrusion Rate, g/min: The technical data contained herein are intended as reference Pressure 0.62 MPa, temperature 25 C : only. Please contact your local quality department for 1/8 Nozzle 550 assistance and recommendations on specifications for this Specific Gravity 25 C 1.04 product. Odor Acetic Acid Storage Flash Point -See MSDS Store product in the unopened container in a dry location. TYPICAL CURING PERFORMANCE Storage information may be indicated on the product container labeling. Surface Cure Optimal Storage: 8 C to 21 C. Storage below 8 C or Tack Free Time is the time required to achieve a tack free greater than 28C can adversely affect product properties . surface. Material removed from containers may be contaminated during Tack Free Time, minutes : use. Do not return product to the original container. Henkel Cured 25 C /505% RH 60 Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than TYPICAL PROPERTIES OF CURED MATERIAL those previously indicated.Ifadditional information is required, Cured for 7 days 25 C /50% RH : please contact your local Technical Service Center or Physical Properties : Customer Service Representative. Shore Hardness, ISO 868 ,Durometer A >25 Conversions TYPICAL ENVIRONMENTAL RESISTANCE (C x 1.8)+ 32 =F kV/mmx 25.4=V/mil The product retains effective properties in contact with mm/25.4=inches automotive fluids, such as motor oil, transmission fluids, N x 0.225=lb alcohol and antifreeze solutions. N/mmx 5.71=lb/in N/mm x 145 =psi NOTE: Not recommended for parts in contact with gasoline. MPa x 145 =psi Nm x 8.851 = lbin Nm x 0.738=lbft Nmm x 0.142=ozin mPas =cP TDS LOCTITE 5926 , November -2004 Note The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection ofproperty and ofpersons against any hazards that may be involved in the handlingand use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage Except as otherwise noted, all trademarks in this document are trademarks of Henkel Corporation in the U.S. and elsewhere. denotes a trademark registered in the U.S. Patent and Trademark Office. Reference 1 Henkel Loctite Americas Henkel Loctite Europe Henkel Loctite Asia Pacific +860.571.5100 +49.89.9268.0 +81.45.758.1810 For the most direct access to local sales and technical support visit: www.loctite.com