Technical Data Sheet LOCTITE ABLESTIK 104 December -2015 PRODUCT DESCRIPTION For optimum performance, follow the initial cure with a post cure of 2 LOCTITE ABLESTIK 104 provides the following product to 4 hours at the highest expected use temperature. characteristics: The above cure profiles are guideline recommendations. Cure Technology Epoxy conditions (time and temperature) may vary based on customers Technology (Part B) Anhydride experience and their application requirements, as well as customer Appearance, Black liquid curing equipment, oven loading and actual oven temperatures. Resin (Component A) Appearance, Hardener White powder (Component B) Components Two component - requires mixing TYPICAL PROPERTIES OF CURED MATERIAL Mixing Ratio, 100 :64 Physical Properties by weight Hardness, Shore D 90 Component A: Component B Coefficient of Thermal Expansion TMA,ppm/C 60 Product Benefits Excellent chemical resistance Glass Transition Temperature DSC/TMA ,C >225 Non-conductive Electrical Properties Highshear strength 15 Volume Resistivity 25C, ohm-cm 10 Hightemperature resistance Dielectric Strength, kV/mm 15.7 Long pot life Cure Heat cure Outgassing Properties Application Assembly Outgassing ,per NASA Reference Publication 1124 ,% : Key Substrates Metals , Glass , Ceramic and Thermoset sample cured 6 hours 120C plastic TML 0.52 Operating Temperature -25 to 230C CVCM 0.08 Chemical Resistance LOCTITE ABLESTIK 104 adhesive is designed for applications Typical Solvent and Chemical Resistance % Weight Change requiring very high temperature exposures . This adhesive can withstand continuous exposure at temperatures as high as 230C .It After 7days Immersion 24 C has also been tested to withstand short term exposures up to 280C . % Weight % Weight Chemical Chemical Change Change TYPICAL PROPERTIES OF UNCURED MATERIAL 30% H2so4 + 0.19 10% NaCl + 0.21 Part A Properties 3% H2so4 + 0.26 5% Phenol + 0.23 Viscosity 25 C, mPas (cP) 25,000 10% NaOH + 0.11 Distilled H2O + 0.20 SpecificGravity 1.35 1% NaOH + 0.22 10% Hno3 + 0.23 Shelf Life 25C, days 183 95% c2h5oh + 0.7 10% HCI + 0.22 Flash Point -See SDS 50% c2h5oh + 0.18 5% ch2cooh + 0.24 Part B Properties Acetone + 0.06 10% nh4oh + 0.76 Shelf Life 25C, days 183 Ethyl Acetate + 0.00 2% Na2CO3 + 0.22 CCl4 + 0.04 3% h2o2 + 0.23 Mixed Properties Working Time, 100 g mass 25 C ,hours >12 Toluene + 0.04 10% Citric Acid + 0.22 Density , g/cm 1.4 Heptane + 0.02 Oleic Acid + 0.09 JP-4 + 0 JP-5 0 TYPICAL CURING PERFORMANCE Cure Schedule 1 hour 200C 2 hours 175C 3 hours 150C 6 hours 120CTDS LOCTITE ABLESTIK 104 , December -2015 TYPICAL PERFORMANCE OF CURED MATERIAL Disclaimer Note: Shear Strength The information provided in this Technical Data Sheet (TDS) including the Tensile Lap Shear Strength : recommendations for use and application of the product are based on our Aluminum to aluminum : knowledge and experience of the product as at the date of this TDS. The product Tested 25 C N/mm 12.4 can have a variety of different applications as well as differing application and working conditions in your environment that are beyond our control. Henkel is, (psi) ( 1,800) therefore, not liable for the suitability of our product for the production processes Tested 150 C N/mm 11.7 and conditions in respect of which you use them, as well as the intended (psi) ( 1,700) applications and results. We strongly recommend that you carry out your own Tested 230 C N/mm 9.7 prior trials to confirm such suitability of our product. (psi) ( 1,400) Any liability in respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal GENERAL INFORMATION injury caused by our negligence and any liability under any applicable mandatory product liability law. For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS). In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV,Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: DIRECTIONS FOR USE In case Henkel would be nevertheless heldliable,on whatever legal ground, 1. Complete cleaning of the substrates should be performed to Henkels liability will in no event exceed the amount of the concerned delivery. remove contamination such as oxide layers, dust, moisture, salt and oils which can cause poor adhesion or corrosion in a bonded In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: part . The information provided in this Technical Data Sheet (TDS) including the 2. Accurately weigh resin and hardener into a clean container in the recommendations for use and application of the product are based on our recommended ratio. Weighing apparatus having an accuracy in knowledge and experience of the product as at the date of this TDS. Henkel is, proportion to the amounts being weighed should be used . therefore, not liable for the suitability of our product for the production processes 3. Blend components by hand, using a kneading motion, for 2 to 3 and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own minutes and scrape the bottom and sides of the mixing container prior trials to confirm such suitability of our product. frequently to produce a uniform mixture . Any liability in respect of the information in the Technical Data Sheet or any other 4. Ifpossible, power mix for an additional 2 to 3 minutes .Avoid high written or oral recommendation(s) regarding the concerned product is excluded, mixing speeds. This can entrap excessive amounts of air. It can except ifotherwise explicitly agreed and except in relation to death or personal also cause overheating of the mixture, resulting in reduced injury caused by our negligence and any liability under any applicable mandatory product liability law. working life. 5. Apply adhesive to all surfaces to be bonded and join together . In case products are delivered by Henkel Corporation, Resin Technology 6. In most applications only contact pressure is required . Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: Not for product specifications The data contained herein are furnished for information only and are believed to The technical data contained herein are intended as reference only. be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to Please contact your local quality department for assistance and determine suitability for the user s purpose of any production methods mentioned recommendations on specifications for this product. herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling Storage and use thereof. In light of the foregoing, Henkel Corporation specifically Store in original, tightly covered containers in clean, dry areas. disclaims all warranties expressed or implied, including warranties of Storage information may be indicated on the product container merchantability or fitness for a particular purpose, arising from sale or use labeling. of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, Optimal Storage : 25C including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Material removed from containers may be contaminated during use. Corporation patents that may cover such processes or compositions. We Do not return product to the original container. Henkel Corporation recommend that each prospective user test his proposed application before cannot assume responsibility for product which has been contaminated repetitive use, using this data as a guide. This product may be covered by one or or stored under conditions other than those previously indicated. If more United States or foreign patents or patent applications. additional information is required, please contact your local Technical Service Center or Customer Service Representative. Trademark usage Except as otherwise noted, all trademarks in this document are trademarks of Henkel Corporation in the U.S. and elsewhere. denotes a trademark Conversions registered in the U.S. Patent and Trademark Office. (C x 1.8)+ 32 = F kV/mm x 25.4 = V/mil mm /25.4 = inches N x 0.225= lb Reference 0.0 N/mm x 5.71= lb/in psi x 145 = N/mm MPa = N/mm Nm x 8.851 = lbin Nm x 0.738= lbft Nmm x 0.142 = ozin mPas = cP Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics