Technical Data Sheet BONDERITE 1455-WWipes November -2012 wetted with fluid. The surface should remain wet for one minute for PRODUCT DESCRIPTION the chmical reaction to be bonded. If handling of the dried, treated work is necessary, operators should wear clean, lint free paint BONDERITE 1455-WWipes provides the following product gloves so that the treated surface is not contaminated. If the treated characteristics: surface becomes damaged or re-contaminated, go back to the first step above. Technology Surface treatment To use only on bare metal surfaces. Application Surface conversion with corrosion Not to use on paint primers 1K, 2K, Polyester fillers, residual paint coatings and plastic parts. protection and enhanced adhesion. 3. Allow the wetted surface to dry at ambient temperature or speed drying with low velocity (do not disturb film) forced warm air up to BONDERITE 1455-WWipes is a chromium free and water- based 100 C max. We recommend a temperature arround 60C (standard corrosion protecting surface treatment for metals like aluminum, paint conditions). zinc, zinc alloy, cold- and hot rolled steel, stainless steel, galvanized, sand basted and armor plate surfaces. BONDERITE 1455-WWipes produce a conversion which forms from a reaction with the above 4. Within 15 minutes apply paint, sealer or adhesive over the dry and mentioned metal surfaces to form true chemical bonds. The converted surface. It is necessary to complete the painting, sealing converted surface provides an excellent base for organic finishes, or adhesive bonding operation. Make sure that all treated surface is paint, sealers and most adhesives. This reaction greatly enhances covered. adhesion and corrosion resistance of subsequently applied paints (including primer when multiple coat systems are used), sealers and adhesives. BONDERITE 1455-WWipes conversion coating process is a dry-in- place application and does not require subsequent cleaning. Storage Temperature, C +10 to +25 Frost- Sensitive yes TECHNICAL DATA Shelf- life 12 months Concentration Ready to use wipes Application Wet the surface by wipe on Evaporation time min. 1 minute Storage requirements: Open time max. 15 minutes Store product in the unopened container in a dry location. Always Ph-value 2.6 reseal the wipe package immediately after removing BONDERITE 1455-WWipes .BONDERITE 1455-WWipes should be protected Application temperature 20 to 40 C from freezing. If the chmemical is frozen, it will be irreversibly damaged and should not be used. When BONDERITE 1455-W Wipes get in contact with the pre-treated surface it could be polluted with surface contamination. To ensure an optimal corrosion protection, the Wipes should be used only once. Wipe that are DIRECTION OF USE accidentally allowed to dry out completely should not be remoistured by adding water to the package dried out wipe should be discarded. To keep wipes moist, reseal any opened package of BONDERITE Preliminary Statement 1455-WWipes using the zip lock closure feature on the package. If Prior to application it is necessary to read the Material Safety Data free fluid accumulates in the bottom of the wipe package, vertically Sheet for information about precautionary measures and safety rotate the package 90 and roll the pack a few times around its own recommendations. Also, for chemical products exempt from axle, the free fluid is re-absorbed by the less moist portion of the compulsory labeling, the relevant precautions should always be unused wipes. observed. Please also refer to the local safety instructions and contact Henkel for analytical support. Application ADDITIONAL INFORMATION Treating metal surfaces with BONDERITE 1455-W Wipes is the last step before starting with sealing, bonding or paint process. Disclaimer: The complete process sequence consists of the following steps: The Information provided herein, especially recommendations for the usage and the application of our products, is based upon our 1. All bare metal surfaces to be converted with BONDERITE knowledge and experience. Due to different materials used as well 1455-W Wipes must be dry and free from grease, oil and other as to varying working conditions beyond our control we strictly foreign matter before pre-treatment. Abrasive cleaning is acceptable recommend to carry out intensive trials to test the suitability of our method of surface preparation where scale or corrosion particles products with regard to the required processes and applications. We exist. Afterward thoroughly clean and prepare the metal surface do not accept any liability with regard to the above information or using Teroson Fl / FL+ or cleaners used in the paint shop (e.g. with regard to any verbal recommendation, except for cases where SiliconeEx). we are liable of gross negligence or false intention. 2. Wipe the clean and dry surface with BONDERITE 1455-WWipes . This datasheet replaces all former versions. Use slightly over lapping vertical and horizontal, even with slightly application pressure. Make sure the entire bare metal surface is Henkel AG & Co. KGaA D-40191Dsseldorf. Germany Phone: +49-211-797-0 www.henkel.com Henkel Central Eastern Europ GmbH A-1030 Wien. Austria Phone: +43-1711-040 www.henkel.com Henkel & Cie AG CH-4133 Pratteln. Switzerland Phone: +41-61-825-7000 www.henkel.com