TechnicalData Sheet LOCTITE 330 November -2007 PRODUCT DESCRIPTION 100 LOCTITE 330 provides the following product characteristics: 75 Technology Acrylic ChemicalType Urethane methacrylate ester Appearance (uncured) Slightly cloudy, colorless to pale 50 LMS yellow liquid Components One component - requires no mixing 25 Viscosity High Cure With activator Application Bonding 0 1min5min10min 30min 1h 3h 6h 24h 72h LOCTITE 330 is a general purpose adhesive that is used to Cure Time bond metal, wood, ferrite, ceramicand plastic materials . TYPICAL PROPERTIES OF CURED MATERIAL Applications includetool handles, appliances, sporting goods Physical Properties : and decorative trim. -6 Coefficientof Thermal Expansion, 810 -1 ISO 11359-2,K TYPICAL PROPERTIES OF UNCURED MATERIAL Coefficientof Thermal Conductivity , ISO8302, 0.1 SpecificGravity 25C 1.05 W/(mK) Flash Point -See MSDS SpecificHeat, kJ/(kgK) 0.3 Viscosity, Brookfield -RVT , 25C, mPas (cP): LMS Spindle 7,speed 20 rpm 45,000 to 90,000 TYPICAL PERFORMANCE OF CURED MATERIAL Viscosity, EN 12092 -SV ,25C, after 180s, mPas (cP): Adhesive Properties -1 Shear rate 20 s 30,000 to 70,000 After 24 hours 22 C ,Activator 7387 on 1 side Lap Shear Strength, ISO 4587: Mildsteel (grit blasted) N/mm 15 to 30 TYPICAL CURING PERFORMANCE (psi) ( 2,175 to 4,350) Cure Speed vs. Substrate TensileStrength, ISO 6922: The rate of cure willdepend on the substrate used. The graph Mildsteel (grit blasted) N/mm 12 to 22 (psi) ( 1,740 to 3,190) below shows the shear strength developed with time on grit blasted steel lap shears and tested according to ISO 4587. After 24 hours 22 C ,Activator 7387 or 7386 on 2 sides (Activator 7387 applied to one surface). TensileStrength, ISO 6922: LMS Mildsteel (grit blasted) N/mm 16.5 100 (psi) ( 2,390 ) TYPICAL ENVIRONMENTAL RESISTANCE 75 Cured for 1 week 22 C ,Activator 7387 on 1 side Lap Shear Strength, ISO 4587: Mildsteel (grit blasted) : 50 0.25mmgap Hot Strength 25 Tested at temperature 100 0 1min5min10min 30min 1h 3h 6h 24h 72h Cure Time 75 Cure Speed vs. Bond Gap The rate of cure willdepend on the bondline gap. The following 50 graph shows the shear strength developed with time on grit blasted steel lap shears at different controlled gaps and tested according to ISO 4587. (Activator 7387 applied to one 25 surface) 0 -50 0 50 100 150 Temperature, C 0.5mm 0.25mm Aluminum Steel 0.05mm % of Full Strength on Steel % of Full Strength on Steel % Strength 22 C120 C TDS LOCTITE 330 , November -2007 LMS Heat Aging Loctite Material Specification Aged at temperature indicatedand tested 22 C LMS dated March -11,1996. Test reports for each batch are availablefor the indicatedproperties. LMS test reports include selected QC test parameters considered appropriate to 125 specifications for customer use. Additionally,comprehensive controls are in place to assure product quality and 100 consistency. Specialcustomer specification requirements may be coordinated through Henkel Quality. 75 Storage Store product inthe unopened container ina dry location. 50 Storage information may be indicatedon the product container labeling. 25 Optimal Storage: 8 C to 21 C. Storage below 8 C or greater than 28 C can adversely affect product properties 0 Material removed from containers may be contaminated during 0 1000 2000 3000 4000 5000 use. Do not return product to the originalcontainer. Henkel Exposure Time, hours Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than Chemical/Solvent Resistance those previously indicated.Ifadditionalinformation is required, Aged under conditions indicatedand tested 22 C. please contact your local TechnicalService Center or % of initial strength Customer Service Representative. Environment C 350h 720h Conversions Acetone 22 10 10 (C x 1.8)+ 32 =F Motor oil(MIL-L-46152) 87 90 66 kV/mm x 25.4=V/mil Unleaded gasoline 22 20 20 mm/25.4=inches m /25.4=mil Phosphate ester 87 93 75 N x 0.225=lb Water/glycol 50/50 87 60 60 N/mmx 5.71=lb/in N/mm x 145=psi GENERAL INFORMATION MPa x 145=psi This product is not recommended for use in pure oxygen Nm x 8.851= lbin and/or oxygen rich systems and should not be selected as Nm x 0.738=lbft a sealant for chlorine or other strong oxidizing materials Nmm x 0.142=ozin For safe handling information on this product, consult the mPas =cP Material Safety Data Sheet (MSDS). Note Where aqueous washing systems are used to clean the The data contained herein are furnished for information only surfaces before bonding, it is important to check for and are believed to be reliable. We cannot assume compatibility of the washing solution with the adhesive. In responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to some cases these aqueous washes can affectthe cure and determine suitability for the user s purpose of any production performance of the adhesive. methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons Directions for use against any hazards that may be involved inthe handlingand 1. For best performance bond surfaces should be cleanand use thereof. In lightof the foregoing, Henkel Corporation free from grease . specifically disclaims all warranties expressed or implied, 2. To ensure a fast and reliablecure, Activator 7387 or including warranties of merchantability or fitness for a 7386 should be applied to one of the bond surfaces and particular purpose, arising from sale or use of Henkel the adhesive to the other surface. Parts should be Corporations products. Henkel Corporation specifically assembled within 15minutes . disclaims any liability for consequential or incidental 3. The recommended bondline gap is 0.1mm.Where bond damages of any kind, including lost profits. The discussion gaps are large (up to a maximum of 0.5mm),or faster herein of various processes or compositions is not to be cure speed is required, Activator 7387 or 7386 should interpreted as representation that they are free from be applied to both surfaces. Parts should be assembled domination of patents owned by others or as a licenseunder immediately(within 1 minute). any Henkel Corporation patents that may cover such 4. Excess adhesive canbe wiped away with organic solvent . processes or compositions. We recommend that each prospective user test his proposed application before repetitive 5.Bond should be held clamped until adhesive has fixtured . use, using this data as a guide. This product may be covered 6. Product should be allowed to develop fullstrength before by one or more United States or foreign patents or patent subjecting to any service loads (typically 24 to 72 hours applications. after assembly, depending on bond gap, materials and ambientconditions) . Henkel Loctite Americas Henkel Loctite Europe Henkel Loctite Asia Pacific +860.571.5100 +49.89.320800.1800 +86.21.2891.8863 For the most direct access to local sales and technical support visit: www.loctite.com 100 C % Initial strength, at RT