Technical Data Sheet LOCTITE 595 September -2004 PRODUCT DESCRIPTION Directions for use LOCTITE 595provides the following product characteristics: 1. For best performance bond surfaces should be clean and Technology Silicone free from grease . Chemical Type Acetoxy silicone 2. Full performance properties will develop over 72 hours . LMS Appearance (uncured) Clear thixotropic paste 3. Moisture curing begins immediately after the product is exposed to the atmosphere, therefore parts to be Components One component - requires no mixing assembled should be mated within a few minutes after the Viscosity Medium, thixotropic product is dispensed . Cure Room temperature vulcanizing (RTV) 4. Excess material can be easily wiped away with non-polar Application Potting ,Coating or Sealing solvents . LOCTITE 595 is designed for superior bonding and sealing LMS Loctite Material Specification properties to most surfaces (not recommended for concrete) . LMS dated September -1, 1995. Test reports for each batch This product resists aging, weathering and thermal cycling are available for the indicated properties. LMS test reports without hardening, shrinking or cracking . It is formulated to include selected QC test parameters considered appropriate to withstand extreme temperature cycling, UV light and ozone . specifications for customer use. Additionally, comprehensive The thixotropic nature of LOCTITE 595reduces the migration controls are in place to assure product quality and of liquid product after application to the substrate . consistency. Special customer specification requirements may be coordinated through Henkel Quality. TYPICAL PROPERTIES OF UNCURED MATERIAL Specific Gravity 25 C 1.01 Storage Extrusion Rate, g/min : Store product in the unopened container in a dry location. Pressure 0.63MPa, time 15 seconds ,temperature 25 C : Storage information may be indicated on the product container LMS Semco Cartridge 100 labeling. Flash Point -See MSDS Optimal Storage: 8 C to 21C. Storage below 8 C or greater than 28C can adversely affect product properties . Material removed from containers may be contaminated during TYPICAL CURING PERFORMANCE use. Do not return product to the original container. Henkel LOCTITE 595cures on exposure to moisture in the air. The Corporation cannot assume responsibility for product which product dries tack free in two hours and fully cures in 24 hours. has been contaminated or stored under conditions other than Cure times will vary with temperature, humidity and gap. those previously indicated. Ifadditional information is required, please contact your local Technical Service Center or TYPICAL PROPERTIES OF CURED MATERIAL Customer Service Representative. Cured for 1 week RT Physical Properties : Conversions LMS Tensile Strength ,ASTM D 412 N/mm 1.5 (C x 1.8)+ 32 =F (psi) (220 ) kV/mm x 25.4 =V/mil LMS Elongation ,ASTM D 412 ,% 350 mm /25.4 =inches LMS Shore Hardness, ASTM D 2240 ,Durometer A 20 N x 0.225=lb N/mm x 5.71=lb/in N/mm x 145 =psi MPa x 145 =psi TYPICAL ENVIRONMENTAL RESISTANCE Nm x 8.851 = lbin Nmm x 0.142 =ozin Silicones provide excellent environmental resistance due to mPas =cP their unique chemical structure and the inherent properties of the materials. Note The data contained herein are furnished for information only GENERAL INFORMATION and are believed to be reliable. We cannot assume This product is not recommended for use in pure oxygen responsibility for the results obtained by others over whose and/or oxygen rich systems and should not be selected as methods we have no control. It is the user s responsibility to a sealant for chlorine or other strong oxidizing materials. determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as For safe handling information on this product, consult the may be advisable for the protection of property and of persons Material Safety Data Sheet (MSDS). against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of HenkelTDS LOCTITE 595, September -2004 Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage LOCTITE is a trademark of Henkel Corporation Reference 1.1 Henkel Loctite Americas Henkel Loctite Europe Henkel Loctite Asia Pacific +860.571.5100 +49.89.9268.0 +81.45.758.1810 For the most direct access to local sales and technical support visit: www.loctite.com