Technical Data Sheet LOCTITE SF 7063 Known as LOCTITE 7063 December -2013 PRODUCT DESCRIPTION GENERAL INFORMATION LOCTITE SF 7063 provides the following product This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected characteristics: with a sealant for chlorine or other strong oxidizing Technology Solvent cleaner materials. Chemical Type Isoparaffin , Dimethoxymethane and Ethanol blend For safe handling information on this product, consult the LMS Appearance Clearcolorless solution Safety Data Sheet (SDS). Viscosity Very low Cure Not applicable Directions for use: Application Surface cleaner 1. Treat surfaces to be cleaned by spraying or wiping surfaces with asolvent soaked paper towel . LOCTITE SF 7063 is a non-CFC solvent based formulation 2. Wipe surfaces when still wet with a clean cloth to remove for cleaning and degreasing of surfaces to be bonded with allheavy contamination. Ifnecessary, spray surfaces LOCTITE adhesives . The product can also be used for again to allow run-off of product . cleaning and degreasing machine components during 3. Repeat cleaning process ifnecessary . maintenance operations . 4. Allow LOCTITE SF 7063 to fully evaporate from parts prior to bonding to avoid solvent entrapment within the TYPICAL PROPERTIES bond joint . Specific Gravity 25C 0.74 LMS 5. Infrared Spectrum As standard Apply the Loctite adhesive immediately after drying and Viscosity 20C, mPas (cP) 2 assemble bond . Drying Time 20 C, seconds 60 LMS Loctite Material Specification TLV (ACGIH),ppm 600 LMS dated December -01,2004. Test reports for eachbatch Flash Point -See SDS are availablefor the indicated properties. LMS test reports include selected QC test parameters considered appropriate to specifications for customer use. Additionally, comprehensive TYPICAL PERFORMANCE controls are in place to assure product quality and LOCTITE SF 7063 has no effecton the speed of cure or consistency. Special customer specification requirements may final strength of LOCTITE adhesives other than providing a be coordinated through Henkel Quality. clean surface for good adhesion and adhesive cure. Unclean Storage or partially cleanedsurfaces can affectadhesive performance. The product is classified as flammable and must be stored in Handling precautions an appropriate manner in compliance with relevant regulations. Do not store near oxidizing agents or combustible Cleaner must be handled in a manner applicable to highly materials. Store product in the unopened container in a dry flammable materials and in compliance with relevant local location. Storage information may also be indicated on the regulations. product container labelling. Special care must be taken to avoid contact of the product or Optimal Storage: 8 C to 21 C. Storage below 8 C or its vapour with nakedflame or any electricalequipment that is greater than 28C can adversely affect product properties . not flame proofed. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel The solvent can affect certain plastics or coatings. It is cannot assume responsibility for product which has been recommended to checkallsurfaces for compatibility before contaminated or stored under conditions other than those use. previously indicated. If additional information is required, please contact your local Technical Service Center or Customer Service Representive. TDS LOCTITE SF 7063 , December -2013 Conversions (C x 1.8)+ 32 = F kV/mm x 25.4= V/mil mm /25.4= inches m /25.4= mil N x 0.225= lb N/mm x 5.71= lb/in N/mm x 145= psi MPa x 145= psi Nm x 8.851 = lbin Nm x 0.738= lbft Nmm x 0.142= ozin mPas = cP Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. The product can have a variety of different applications as well as differing application and working conditions in your environment that are beyond our control. Henkelis, therefore, not liablefor the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liabilityin respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except if otherwise explicitly agreedand except in relation to death or personal injury caused by our negligence and any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkelwould be nevertheless heldliable,on whatever legalground, Henkels liabilitywill in no event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkelis, therefore, not liablefor the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liabilityin respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except if otherwise explicitly agreedand except in relation to death or personal injury caused by our negligence and any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believedto be reliable.We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as aguide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage Except as otherwise noted, alltrademarks in this document are trademarks of HenkelCorporation in the U.S. and elsewhere. denotes a trademark registered in the U.S. Patent and Trademark Office. Reference 1.1 Henkel Americas Henkel Europe Henkel Asia Pacific +860.571.5100 +49.89.320800.1800 +86.21.2891.8859 For the most direct access to local sales and technical support visit: www.henkel.com/industrial