Technical Data Sheet LOCTITE 7200 June -2005 PRODUCT DESCRIPTION 4. Remove gasket with soft scraper and wipe flange or surface clean, repeat procedure ifnecessary . LOCTITE 7200 provides the following product 5. characteristics: Before application of new gasketing material, it is Technology Solvent- Based essential to clean the flange or surface with appropriate Chemical Type Mixture of aliphatic glycol ethers, solvents such as Loctite 7063 . hydrocarbons, surfactants and Handling precautions methyl ethyl ketones Pressurised container. Protect from sunlight and do not LMS Appearance Amber liquid expose to temperatures exceeding 50 C. Do not pierce or Solubility in Water Immiscible burn, even after use. Do not spray on an open flame or any Solubility in Solvents Miscible incandescent material . Propellant Propane LMS Loctite Material Specification Cure Not applicable LMS dated December -09, 2004 . Test reports for each batch Application Cleaner are availablefor the indicated properties. LMS test reports SpecificBenefit Easy application from an include selected QC test parameters considered appropriate to aerosol can specifications for customer use. Additionally, comprehensive Willnot run, even on vertical controls are in place to assure product quality and surfaces consistency. Special customer specification requirements may Does not contain CFC be coordinated through Henkel Quality. LOCTITE 7200 is designed to aid removal of cured Storage The product is classifiedas flammable and must be stored in chemical gaskets by softening the gasket material on the an appropriate manner in compliance with relevant flanges, eliminating excessive scraping . Once applied, the regulations. Do not store near oxidizing agents or combustible product develops a foam-likelayer on the gasket, preventing it materials. Store product in the unopened container in a dry from running off the desired location, thus allowing itto work for location. Storage information may also be indicated on the the required duration .Typical applications include removal of product container labelling alltypes of chemical gaskets from metal flanges . It is Optimal Storage: 8 C to 21 C. Storage below 8 C or greater than 28 C can adversely affect product properties . particularly suitable for removing gaskets from aluminum or Henkel cannot assume responsibility for product which has other soft metal flanges where excessive scraping could easily been contaminated or stored under conditions other than those lead to flange surface damage . It may also be used to aid previously indicated. Ifadditional information is required, removal of adhesives, baked-on grease or oil,built-up carbon please contact your local Technical Service Center or deposits, dried oils, paint, varnish, etc. from metal flanges or Customer Service Representive surfaces . Conversions (C x 1.8)+ 32 =F NOTE: LOCTITE 7200 is intended mainly for metal kV/mm x 25.4 =V/mil components. It is not recommended for use on plastic mm /25.4 =inches components . N x 0.225=lb N/mm x 5.71=lb/in TYPICAL PROPERTIES LMS N/mm x 145 =psi SpecificGravity 25 C 0.86 to 0.9 LMS MPa x 145 =psi pH 20 C 10.6 to 11.0 Nm x 8.851 = lbin Dry Residue, % ~4 Nm x 0.738=lbft Flash Point -See MSDS Nmm x 0.142 =ozin mPas =cP GENERAL INFORMATION Note For safe handling information on this product, consult the The data contained herein are furnished for information only Material Safety Data Sheet (MSDS). and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose Directions for use methods we have no control. It is the user s responsibility to 1. Protect painted surfaces thoroughly from over-spray, as determine suitability for the user s purpose of any production LOCTITE 7200 willattack the paint . methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons 2. For best results, hold can upright, 20 to 30 cm away from against any hazards that may be involved in the handling and gasket area or surface and spray onto the flange or use thereof. In lightof the foregoing, Henkel Corporation surface, the heavier the coat the better . specifically disclaims all warranties expressed or implied, 3. Allow 10 to 15 minutes to soften the gasket, for silicone including warranties of merchantability or fitness for a gaskets allow 30 minutes . TDS LOCTITE 7200 , June -2005 particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage Except as otherwise noted, alltrademarks in this document are trademarks of Henkel Corporation in the U.S. and elsewhere. denotes a trademark registered in the U.S. Patent and Trademark Office. Reference 1.0 HenkelLoctite Americas HenkelLoctite Europe HenkelLoctite Asia Pacific +860.571.5100 +49.89.9268.0 +81.45.758.1810 For the most direct access to local sales and technical support visit: www.loctite.com