Technical Data Sheet LOCTITE MSC 1000S Formerly known as SPOT-ON August -2017 PRODUCT DESCRIPTION Do not over cure, as blistering of mask can occur, causing removal LOCTITE MSC 1000S provides the following product characteristics: problems. Technology Temporary Solder Resist Application Soldering RECOMMENDED CURE Color Opaque white liquid Recommended Application Thickness ,mm 2.0 Odor Ammoniacal Typical Cure Time 2 hours 25C LOCTITE MSC 1000S is a peelable, temporary solder resist designed to be applied to the printed circuit board prior to soldering to mask 40 minutes 80C areas where components need to be placed after wave soldering .It is Removal formulated to withstand fluxing and wave soldering applications .This material can be used in conjunction with fluxes whose residues do not Must be removed .Peel off,DO NOT ATTEMPT TO WASH OFF (not require removal after soldering . soluble in water or other solvents) . FEATURES AND BENEFITS Easily peelable PACKAGING Withstands high temperatures LOCTITE MSC 1000S is available in 250 ml bottles . Long shelf life Thixotropic -holds position STORAGE AND SHELF LIFE Non-flammable LOCTITE MSC 1000S has a 1 year shelf lifeat room temperature. It is Non-ozone depleting important that this material is not stored below 5C to prevent Compatible with gold finishes irreversible separation of the material. Non-corrosive GENERAL INFORMATION APPLICATIONS For safe handling information on this product, consult the LOCTITE MSC 1000S is suitable for hand, robotic, pneumatic or Material Safety Data Sheet (MSDS). template screening applications. This material should be removed after soldering by peeling off. Not for Product Specifications LOCTITE MSC 1000S can also be applied by brush . The technical information contained herein is intended for reference It is particularly suited for use on gold, silver or pre-soldered only. Please contact Henkel Technologies Technical Service for surfaces . assistance and recommendations on specifications for this product. This material can be used on copper but some surface degradation and/or drop in solderability may be observed. It is Conversions therefore recommended that LOCTITE MSC 1000CUS be (C x 1.8)+ 32 = F used for copper surfaces . kV/mm x 25.4= V/mil mm /25.4= inches m /25.4= mil RECOMMENDED OPERATING CONDITIONS N x 0.225= lb The substrate should be free of grease, oil, and particulates . N/mm x 5.71= lb/in LOCTITE MSC 1000S should be applied at a liquid coating N/mm x 145= psi thickness of 2.0mm (80 thou) to ensure a coherent film for ease MPa x 145= psi of subsequent removal as it dries to a thinner coating . Nm x 8.851 = lbin Drying times depend upon ambient humidity and temperature. Nm x 0.738= lbft Under normal conditions LOCTITE MSC 1000S is ready for the Nmm x 0.142= ozin soldering process in two hours. This may be accelerated to 40 mPas = cP minutes at 80C (180F). LOCTITE MSC 1000S must be completely dry prior to wave soldering to ensure complete removal post soldering.TDS LOCTITE MSC 1000S , August -2017 Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. The product can have a variety of different applications as well as differing application and working conditions in your environment that are beyond our control. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability in respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless held liable, on whatever legal ground, Henkels liability will in no event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability in respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage: Except as otherwise noted All trademarks in this document are trademarks and/or registered trademarks of Henkel and its affiliates in the U.S. and elsewhere. Reference 3 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.2891.8000 For the most direct access to local sales and technical support visit: www.henkel.com/electronics