TechnicalData Sheet LOCTITE C 511 September -2014 PRODUCT DESCRIPTION soldering iron design and the nature of the task. LOCTITE C 511 provides the following product characteristics: Care should be exercised to avoid unnecessarily high tip temperatures for extensive periods of time. Technology Cored solder wire A hightip temperature may increase any tendency to fluxspitting Activity High and it may produce some residue darkening. Product Benefits No clean The tip of the soldering iron should be properly tinned. Severely contaminated soldering iron tips should be cleaned with Clearresidue Multicore Tip Tinner/Cleaner. Good wetting Wipe the tip on a clean, damp sponge before re-tinning with Fast soldering LOCTITE C 511 wire. Heat stable Mildodor Soldering Process: Pb-freeand SnPb alloys available 1. Apply the soldering iron tip to the work surface. The iron tip IPC/J-STD-004 ROM1 should contact both the base material and the leadat the same Classification time to heat both surfaces properly. It should take no more than a fraction of a second to heat both surfaces adequately. Application Soldering -Cored wire 2. Apply LOCTITE C 511 flux cored wire to a part of the joint Surface Finishes Copper ,Brass and Nickel surface away from the soldering iron and allow to form a joint fillet. This willbe virtually instantaneous. Do not apply excessive LOCTITE C 511 cored solder wire has been specially formulated to solder to the joint as this willnot improve joint integrity and it will complement no clean wave and reflow soldering processes. leave excess fluxresidues on the surface. 3. Remove solder from the work piece and then remove the iron tip. TYPICAL PROPERTIES 4. The total process willbe very rapid, depending upon thermal mass, tip temperature, tip configuration and the solderability of Solder Wire -Cored Typical Properties the surfaces to be joined. Alloys -Tin/lead SN63 5. The resin and flux systems are designed to leave relatively low residues and to minimize residual activity. This is achieved by SN60 ensuring some decomposition and volatilization takes place SN62 during the soldering process 60EN Alloys -Lead Free 96SC(SAC387) Cleaning: 97SC(SAC305) LOCTITE C 511 flux cored solder wire has been formulated to leave 99C(SnCu) amber flux residues and resist spitting and fuming. In most industrial 95A (SnSb) and consumer electronics applications, cleaning will not be required. The product may, therefore, be used to complement a 96S(SnAg) no-clean wave soldering or reflow process or to allow repairs to AcidValue 164 to 176mg KOH/g cleaned boards without the need for a second cleaning process. In Halidecontent 1.1% high-reliabilityapplications, the residues should be removed. Flux Content (%) 2.7 Should cleaning be required, this is best achieved using SC-01 ALLOYS: cleaner. The alloys used in LOCTITE C 511 cored solder wires conform to the purity requirements of the common national and international standards . RELIABILITY PROPERTIES FLUX: LOCTITE C 511 solid flux is based on modified rosin and carefully selected activators. In practice they exhibit a mildrosin odor and leave J-STD-004 Solder spread mm 340 a smallquantity of clearresidue . Corrosion Test Pass SIR(without cleaning) IPC-SF-818Class 3 Pass Bellcore Pass DIRECTIONS FOR USE TR-NWT- 000078 Soldering with LOCTITE C 511 does not require any special methods Electromigration (without cleaning) Bellcore Pass or deviation from standard hand soldering practices. TR-NWT- 000078 Classification EN29454- 1 1.1.2 Soldering Iron: IPC-SF-818 MR3CN Good results can be obtained using a range of tip temperatures. However, the optimum tip temperature and heat capacity required for a hand-soldering process is a function of bothTDS LOCTITE C 511, September -2014 relation to death or personal injury caused by our negligence and any PACKAGING liabilityunder any applicablemandatory product liabilitylaw. LOCTITE C 511 is availablein various diameters, flux percentages, and reelsizes. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada, Inc.the following disclaimer is applicable: DATA RANGES The data contained herein are furnished for information only and are The data contained herein may be reported as a typical value believedto be reliable.We cannot assume responsibility for the results and/or a range. Values are based on actual test data and are obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of verifiedon a periodic basis . any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of GENERAL INFORMATION persons against any hazards that may be involved in the handling and For safe handling information on this product, consult the use thereof. In lightof the foregoing, Henkel Corporation specifically Material Safety Data Sheet (MSDS). disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, Not for Product Specifications arising from sale or use of Henkel Corporations products. Henkel The technical information contained herein is intended for reference Corporation specifically disclaims any liability for consequential only. Please contact Henkel Corporation Technical Service for or incidental damages of any kind, including lost profits. The assistance and recommendations on specifications for this product. discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of Conversions patents owned by others or as a license under any Henkel Corporation (C x 1.8)+ 32 =F patents that may cover such processes or compositions. We kV/mm x 25.4 =V/mil recommend that each prospective user test his proposed application mm /25.4 =inches before repetitive use, using this data as a guide. This product may be m /25.4 =mil covered by one or more United States or foreign patents or patent N x 0.225=lb applications. N/mm x 5.71=lb/in N/mm x 145 =psi Trademark usage MPa x 145 =psi Except as otherwise noted, alltrademarks in this document are Nm x 8.851 = lbin trademarks of Henkel Corporation in the U.S. and elsewhere. Nm x 0.738=lbft denotes a trademark registered in the U.S. Patent and Trademark Nmm x 0.142 =ozin mPas =cP Office, Disclaimer Reference 0.2 Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. The product can have a variety of different applications as wellas differingapplication and working conditions in your environment that are beyond our control. Henkel is, therefore, not liablefor the suitability of our product for the production processes and conditions in respect of which you use them, as wellas the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liabilityin respect of the information in the TechnicalData Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitlyagreed and except in relation to death or personal injury caused by our negligence and any liabilityunder any applicablemandatory product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless heldliable,on whatever legal ground, Henkels liabilitywillin no event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkel is, therefore, not liablefor the suitability of our product for the production processes and conditions in respect of which you use them, as wellas the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liabilityin respect of the information in the TechnicalData Sheet or any other written or oral recommendation(s) regarding the concerned Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics