ELP331M2GBA Hitano

ELP SERIES l Directly mountable on printed circuit board without holders. l Smaller low profile sizes than ordinary capacitors. l Terminal spacing fixed at 10mm for PC board plug in. l Aluminum case designed explosion-proof vent. Characteristics Voltage Range 16 ~ 100V 160 ~ 450V 680 ~ 47000uF 47 ~ 2200uF Capacitance Range Temperature Range -40 ~ +85 -25 ~ +85 Capacitance Tolerance 20% at 120Hz , 20( 10% Tol. is available upon request) Leakage Current I=3 uA max C: Capacitance, V:W.V. (After 5 minutes) CV Dissipation Factor(tan) Less than the value under table (%) 10 16 25 35 50 63 80 100 160 250 350 450 uF W.V. ( at 20, 120Hz) 47 390 - - - - 15 20 470 3900 25 20 20 20 15 20 47008200 35 30 30 25 1000022000 40 35 30 2700047000 45 40 35 Stability at Low Temperature Impedance ratio at 120Hz between the -25 or -40 value and 20 value shall not exceed : Z-25/Z 20 3 Z-40/Z 20 12 Load Life The following specifications shall satisfied when the capacitors are restored to 20 after rated working voltage applied for 2,000 hours at max. operating temperature with the rated ripple current applied. Capacitance change 20% of the initial value. Dissipation factor 200% of the initial specified value Leakage current The initial specified value. Shelf Life After storage for 1000 hours at 85 with no voltage applied, the capacitor shall meet the specified limit in load life. Diagram of dimensions Multiplier for R.C. vs Temparature (mm) Temp.() 45 60 70 85 Dia 22 25 30 35 Multiplier 1.55 1.3 1.2 1.00 2 2 3 3 Multiplier for Ripple Current VS Frequency Cap.(uF) (Hz) 60 120 1K 10K 50K - 100K 0.8 1 1.36 1.48 1.53 10Cap.100 100Cap.1000 0.8 1 1.25 1.35 1.38 0.8 1 1.17 1.25 1.28 1000Cap. 37 ELP SERIES Standard Products Table Ripple Dimensions A Dimensions B Dimensions C Current A W.V(DC) CAP. (F) max. 85, D L D L D L 120Hz 4700 2.40 22 25 - - 6800 2.84 22 25 - - 10000 3.06 22 30 25 25 - 15000 3.94 22 35 25 30 - 16 22000 4.80 22 45 25 35 30 30 33000 8.20 25 50 30 40 - 47000 8.96 30 50 35 40 - 4700 2.64 22 25 - - 6800 2.93 22 30 25 25 - 10000 3.43 22 40 25 35 - 25 15000 4.39 22 50 25 40 30 35 22000 5.40 25 50 30 40 - 33000 6.24 30 50 35 40 - 47000 7.60 35 50 - - 2200 2.18 22 25 - - 3300 2.46 22 25 - - 4700 2.68 22 30 25 25 - 6800 3.06 22 35 25 30 - 35 10000 3.60 25 45 30 35 - 15000 3.92 25 50 30 40 - 22000 5.45 30 45 35 40 - 33000 6.36 35 50 - - 2200 2.04 22 25 - - 3300 2.64 22 30 25 25 - 4700 2.88 22 35 25 30 - 50 6800 3.24 22 50 25 40 30 30 10000 3.96 25 50 35 40 - 15000 4.70 30 50 - - 22000 5.85 35 50 - - 1000 1.58 22 25 - - 2200 2.52 22 25 25 25 - 3300 3.12 22 40 25 30 - 63 4700 3.28 25 45 30 35 - 6800 4.32 25 50 30 40 - 10000 4.77 35 50 - - 1000 1.62 22 25 - - 2200 2.52 22 40 25 30 - 3300 3.24 22 50 25 40 30 30 80 4700 3.60 25 50 30 40 6800 4.60 30 50 35 40 - 10000 5.04 35 55 - 680 1.53 22 25 - - 1000 1.62 22 30 25 25 - 1500 1.85 22 40 25 35 30 30 100 2200 2.64 22 50 25 40 30 30 3300 3.42 25 50 30 40 - 4700 3.72 30 50 35 40 - 6800 4.10 35 50 - - 38