Manuals Manual Switches AML45/59 Series Solid State LED Annunciators FEATURES 1 Messages are backlighted with LEDs for long, reliable operating life. Reduces service and maintenance costs. 1 Low voltage and current (without inrush), enables direct drive with integrated circuits. Reduces cost of interface components (and installation), and power supply. 1 Low operating temperature allows high-density, continuous operation. Minimal heat build-up. 1 Inherently rugged. Resists effects of shock and vibration (no filaments to break). 1 High density message display. Illuminates up to four legend sectors in color, in a 0.8 1.2 inch area. 1 Dead front hides legends until illuminated. Non-glare display with no flickering. 1 UL recognized. AML45/59 solid state LED annunciators Film legends offer a choice of negative or NEGATIVE are a state-of-the-art advancement over positive formats. (Note: human factors When illuminated, colored legend ap- traditional back-lighted legend displays engineers generally favor negative an- pear1001s against a black background. which utilize incandescent lamps. The nunciator messages, reserving the posi- LED light source imparts the benefits of tive format for use if special attention is NEGATIVE solid state long-life and reliability, with low necessary, such as PAPER JAM.) power requirements. Operating life is POSITIVE measured by years, instead of hours. When unlighted, the legend is hidden (dead front). When illuminated, black legend appears The AML45 housing has two high effi- against a colored background. ciency LEDs which illuminate color filters and film legends located in the snap-on POSITIVE AML59 cap assembly. There is a choice of full face one-color and split one-color or This annunciator is totally compatible two-color displays. Color options are red, with other deivces in the MICRO SWITCH green, and yellow. AML Advanced Manual Line both in front of, and behind the panel. Two of them fit in the same space as a rectangular AML indicators or switch. All terminals exit at AMLs standard 1.7-inch depth for conve- nient, single-level wiring. Honeywell1 Sensing and Control1 1-800-537-6945 USA1 F1-815-235-6847 International 1 1-800-737-3360 Canada 37Manual Switches AML45/59 Series Solid State LED Annunciators AML45 LED HOUSINGS LEDs should be specified as the same color if a full or split screen one-color display is desired (RR = red) or different colors for a split screen two-color display (RY = red/yellow). (Baffle plate inside housing prevents light spillage from one LED color section to the other on split screen versions.) LED colors should match filter colors specified in AML59 cap assembly (see page 40). Spring clips on sides of the housing hold units securely in panel. For mounting strips of two or more units, AML61 mount- ing hardware may be used (see page 55). LED APPLICATION INFORMATION PANEL ORIENTATION Refer to page 59. Drawing (above) indicates Side 1 and colors, such as RG (red/Side 1, green/ Side 2 LED locations, with MICRO Side 2). Since LEDs are permanently in- SWITCH identifications facing UP. Con- stalled, color location is specially impor- sider this orientation when ordering an tant to note when the device is to be termi- AML45S housing with two different LED nated in a printed circuit board. AML45 ORDER GUIDE AML45 S W A 2 RY LED Color Housing Color of LED Terminal Type Housing Bezel Voltage* Type Side 1 Side 2 AML45 R W A 2 R R 2 LEDs White 2.4 V .110 .020 Red Red (For use with (Solder or Full Screen) K B Quick-Connect) Y Y Black 5V Yellow Yellow AML45 S 3 2 LEDs C .025 .025 G G (For use with 10 V (Printed Circuit) Green Green Split Screen) D 8 15 V .110 .020 with diode protection F for LEDs 24 V * Current draw is 20 mA. B, Example: AML45SWA2RY C, D and F have built-in Split screen type housing with white bezel, current limiting resistors. 2.4 V LEDs, .110 .020 termination, red LED in Side 1 and yellow LED in Side 2. 38 Honeywell1 Sensing and Control1 1-800-537-6945 USA1 F1-815-235-6847 International 1 1-800-737-3360 Canada