HFE7000-210 Honeywell

Fiber Optic Components 50 Mbps 650 nm LED HFE7000-210 FEATURES Super bright LED for optical fiber communication Integrated lens provides maximum coupling into plastic fibers High power output at 650 nm High speed (50 Mbps) High reliability Designed to meet SERCOS requirements HFE7000-210 WARNING DESCRIPTION The HFE7000-210 is a 50 Mbps LED designed to meet the data PERSONAL INJURY DO NOT USE these products as transmission requirements needed in factory and office automation. safety or emergency stop The 650 nm wavelength provides operation for the low attenuation area devices, or in any other applica- of PMMA (Polymethylmethacrylat) fibers. The plastic SMA housing tion where failure of the product delivers a cost-effective module that can be easily mounted on a PCB. could result in personal injury. The HFE7000-210 is designed to work with Honeywells high-speed Failure to comply with these receivers, HFD7000-XXX and HFD7500-XXX. instructions could result in APPLICATIONS death or serious injury. Designed for data transmission in factory automation and office settings. The HFE7000-210 delivers high speed and short distance links. WARNING FIGURE 1. PACKAGE INFORMATION MISUSE OF DOCUMENTATION Outline dimensions mm in (for reference only) The information presented in this product sheet is for reference only. Do not use this document as a product installation guide. Complete installation, opera- tion, and maintenance infor- mation is provided with each product. Failure to comply with these instructions could result in death or serious injury. NOTICE Stress greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the opera- tional section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Sensing and ControlFiber Optic Components HFE7000-210 50 Mbps 650 nm LED ABSOLUTE MAXIMUM RATINGS (T = 25 C 77 F ) A Parameter Symbol Rating Forward current If 40 mA Reverse voltage V 5 V R 1 Power dissipation P 250 mW Max Soldering temperature T 230 C 446 F for 5 sec Sold Operating temperature T 0 C to 70 C 32 F to 338 F Op Storage temperature T -40 C to 85 C -40 F to 185 F Stor 1 Derate power dissipation at a rate of 1.7 mW/C above T = 25 C 77 F . A ELECTRO-OPTICAL CHARACTERISTICS (T = 25 C 77 F ) A Parameters Test Condition Symbol Min. Typ. Max. Unit Data rate Driven by recommended circuit f dc 50 Mbps D Forward voltage If = 20 mA Vf 1.9 2.3 V Reverse current Vr = 5 V Ir 10 A If = 10 mA Po -10 dBm Output power If = 20 mA Po -7 dBm Peak wavelength If = 20 mA lp 650 nm 1 Spectral halfwidth If = 20 mA Dl 20 nm 2 Rise time If = 20 mA tr 8 ns 2 Fall time If = 20 mA tf 8 ns 1 Output from a 1,0 m 39.37 in long, 1,0 mm 0.04 in diameter plastic fiber (GH4001 made by Mitsubishi Rayon). Measured with recommended drive circuit. 2 Time required for change in the output as shown below. Measured with recommended drive circuit (Figure 7). FIGURE 2. TYPICAL OUTPUT WAVEFORM FIGURE 3. RISE/FALL TIME (T =25 C 77 F , If = 20 mA, 5 ns/div.) A ORDER GUIDE Catalog Listing Description HFE7000-210 650 nm LED in plastic SMA housing 2 Honeywell Sensing and Control