Manuals Manual Switches MML92/93 Series LEDs LED APPLICATION INFORMATION To insure stable conditions, suitable ex- Resistor values can be determined by ternal control of the LED current must be supply voltage or current for LED: provided. It is recommended that a mini- EV f mum of 5 VDC open circuit voltage with RS = I f an appropriate series resistance be used to drive LED devices. This minimizes cur- rent variation and its effect on temper- ature and forward voltage of the LED. WHERE: RS = Series Resistance Maximum drive current is 30 mA. Reverse E = Supply Voltage voltage breakdown of the LEDs is 4 volts V = Forward Voltage f (min.). of LED I = Circuit Current f MML92 ORDER GUIDE LEDs should be the same color as the lenses they illuminate. They are packed 10 per listing, including stand-off spacers for use when solder terminating to a printed wiring board, per procedure 3 on page 86. Forward LED LED Use To Catalog LED Characteristics Manufacturers Type Illuminate Listing Color Typ. 20mA Max. Part Numbers 3 T1 4 Rectangular Stanley: button lens MML92ERS Red 1.7 V 2.0 V ESBR5633 MML92EGS Green 2.1 V 2.5 V ESBG5633 MML92EYS Yellow 2.1 V 2.5 V ESAY5633 Hewlett Packard: MML92ERH Red 2.2 V 3.0 V HLMP-3366 MML92EGH Green 2.3 V 3.0 V HLMP-3568 MML92EYH Yellow 2.2 V 3.0 V HLMP-3466 T1 Square button Stanley: lens, MML24 MML92HRS Red 1.7 V 2.0 V ESBR3901 rocker lens MML92HGS Green 2.1 V 2.5 V ESPY3901 rectangular MML92HYS Yellow 2.2 V 2.5 V ESAY3901 button lens Hewlett Packard: MML92HRH Red 2.2 V* 3.0 V HLMP-1340 MML92HGH Green 2.3 V* 3.0 V HLMP-1540 MML92HYH Yellow 2.2 V 3.0 V HLMP-1440 Long lead: Anode (+). Short lead: Cathode (-). * 25mA. MML93 LED PWB RECEPTACLE ORDER GUIDE MML93 LED SOLDER TERMINAL ORDER GUIDE LED Catalog LED Catalog Type Use to Illuminate Listing Type Use to Illuminate Listing 3 T-1 4 Rectangular button lens or umbrella button T-1 Square button (base only) MML93L lens MML93K T-1 MML24 rocker lens (base only) MML93R T-1 Square button lens or MML24 rocker lens MML93G T-1 Rectangular button MML93J (base and terminal) Honeywell1 Sensing and Control1 1-800-537-6945 USA1 F1-815-235-6847 International 1 1-800-737-3360 Canada 85Manual Switches MML92 Series LEDs Factory installed. Certain MML switches User installed. LEDs can also be ordered and indicators can be furnished with separately and installed in these products LEDs permanently factory installed, by the user, per the procedures de- where specified in the order guides. scribed below. LED INSTALLATION 1. With Printed Wiring Board Receptacle. (MML93K) 3 PWB receptacle enables T-1 4 or T-1 LEDs to be added or replaced from behind the printed wiring board, with- out soldering. LEDs and receptacles are ordered separately. See page 87. Printed wiring boards are not supplied. 1 1. Insert the LED/PWB receptacle as- 2. A 8turn applied clockwise to the re- sembly through a hole in the printed ceptacle locks it in the printed wiring wiring board. board and establishes the electrical connection. 2. With Solder Terminal Receptacle. (MML93J) This receptacle attaches directly to the rear of panel-mounted units. It enables incandescent lamps to be added or replaced without rewiring. LEDs and receptacles are ordered separately. This receptacle is for use with all rect- angular pushbuttons and MML41 or MML46 rectangular indicators only. 1 2. A 8turn clockwise applied to the re- 1. Insert solder terminal receptacle into ceptacle locks it in the base. hole in base of panel mount unit. 3. By Soldering To Printed Wiring Board. In this procedure, the housing is mounted on the printed wiring board 3 after the T-1 4 LED has been seated. This procedure can be used with any MML having PWB terminals. 1. Assemble stand-off spacer to LED ter- 2. Seat housing on printed wiring board, minals and seat on printed wiring with LED projecting into hole at the board. base of the housing. 4. By Soldering to Printed Wiring Board or Leadwire (MML44 indicators only). 3 T-1 4 LEDs are added to MML44 in- dicators via a procedure which is unique to this product. The LED is in- serted from the top of the housing with the leadwires protruding through the housing base. 1. Assemble LED to MML44 indicator, 2. Use pencil eraser to snap LED securely with the LED terminals protruding in place. through assembly slot in the middle of housing base. 86 Honeywell1 Sensing and Control1 1-800-537-6945 USA1 F1-815-235-6847 International 1 1-800-737-3360 Canada