INSTALLATION INSTRUCTIONS FOR THE 32347440 Issue A SPEED SENSORS, SNG-S SERIES positioned at the circumference of a revolving gear wheel GENERAL SPECIFICATIONS detects the teeth and spaces, and supplies a digital pulse Honeywells SNG-S Series Speed Sensors use a magnetically output with frequency proportional to gear wheel speed. biased Hall-effect integrated circuit (IC) to accurately sense Optimum performance is dependent upon a combination of movement of ferrous metal targets. The specially designed variables such as target material, geometry and speed, sensor/ IC and a permanent magnet are sealed in rugged, probe- target gap, and environmental temperature. type packages. The IC detects the alteration of the magnets flux density when it is approached by ferrous metal. A sensor TABLE 1. ELECTRICAL SPECIFICATIONS PARAMETER SNG-SPRD-002 CHARACTERISTIC CONDITION/COMMENT SNG-SPRD-003 SNG-SPRD-004 SNG-SPRF-002 SNG-SPSC-001 SNG-SPRC-002 SNG-SPRC-003 SNG-SPRC-001 regulated supply and 12 V battery 4.5 V to 24 V Supply voltage ISO 16750-2 8 V to 16 V 4.8 V to 16 V 4.8 V to 24 V Supply current 20 mA max. 15 mA Reverse voltage -24 V protection ISO 16750-2 -14 Vdc Over voltage 26.5 V protection ISO 16750-2 26 V Short circuit 16 V protection ISO 16750-2 16 V ISO 16750-2:2012 11 01 5b Load dump (US* = 40 V, UA 13.5 0.5 V) >10 MOhm at 500 Vdc Insulation resistance ISO 16750-2:2012 TABLE 2. MECHANICAL SPECIFICATIONS PARAMETER SNG-SPRD-002 CHARACTERISTIC SNG-SPRD-003 SNG-SPRD-004 SNG-SPRF-002 SNG-SPSC-001 SNG-SPRC-002 SNG-SPRC-003 SNG-SPRC-001 Carrier material PBT thermoplastic PBT Bushing material SS304 SSTL 70 durometer fluorocarbon, PTFE coating, O-ring material fluorocarbon, brown, 17,17 mm ID x 1,78 CS 17,17 mm ID x 1,78 CS Housing material PBT PBT Connector: integral Bosch 928000453 Amp Superseal 1.5 mating Bosch 1928403966 282087 Mounting torque 8 0,5 N m with M6 screw 20 3 N m with M8 screw O-ring lubrication mineral oil-based greaseSPEED SENSORS, SNG-S SERIES Issue A 32347440 TABLE 3. ENVIRONMENTAL SPECIFICATIONS PARAMETER CHARACTERISTIC CONDITION/COMMENT SNG-SPRF-002 ALL OTHER CATALOG LISTINGS ISO 11452-2: 2004 10 kHz to MHz, 60 m/V ISO 11452-2: 2004 200 MHz to 2.7 GHz, 100 V/m Radiated immunity IEC 61000-4-3: 2008 800 kHz MHz to 1000 MHz, 3 m/V ISO 11452-2, 400 MHz to 2.5 GHz 100 V/m Bulk current injection ISO 11452-4, 1 MHz to 400 MHz 100 mA SAE J1113/13 4 kV contact, 8 kV air ESD ISO 10605 8 kV contact, 15 kV air ISO 7637-2, for 12 V system TEST PULSE 1, 2a, 2b, 3a, 3b Conductive transients ISO 7637-2, for 12 V system PULSE 1, 2a, 3a, 3b, 5a Conducted emissions CISPR 25. 150 kHz to 108 MHz Class 3 Radiated emissions CISPR 25. 150 kHz to 12.5 GHz Class 3 Thermal cycle -40C to 140C 100 cycles 10 %RH to 90 %RH at -40C to 85C, Humidity 150 cycles, 600 hr total 95 %RH at 55C 144 hr, EN/IEC 60068-2-30 Saline dunk 0C to 110C 10 cycles, ISO 16750-4 5% salt solution by mass at 35C and 93% RH 5% salt solution by mass at 35C and for 400 hr, tested to 2000 hr with no ingress in 93% RH for 2000 hr Salt fog the sensor packaging area 5% salt solution by mass at 35C 96 hours sinusoidal: 25 hr/axis, 3 perpendicular axes sinusoidal: 25 hr/axis, 3 perpendicular axes 30 g at 60 Hz to 1000 Hz and 15 g at 15 g at 5 Hz to 2000 Hz Combined temperature and 1000 Hz to 2000 Hz vibration test random: 25 hr/axis, 3 perpendicular axes 30 g random: 25 hr/axis, 3 perpendicular axes at 25 rms Hz to 2000 Hz, -40C to 125C at 25 grms at 10 Hz to 2000 Hz 29.8 GRMS, 24 Hz to 2000 Hz, Vibration 3 perpendicular axes, 48 hr per axis MIL-STD-202-214 IEC 50629 IPX6, IPX9K, IPX7 Degree of protection IEC 60529 IP69K, IP67 Resistance to fluids general under-the-hood automotive fluids Operating temperature -40C to 150C -40C to 140C Storage temperature -55C to 70C -40C to 140C S 2 sensing.honeywell.com