ISSUE 2 Installation Instructions for the MICRO SWITCH V15W Series Watertight 50066512 Miniature Switches Satisfying this test condition does not mean that the WARNING switch can be used in water. Switches with terminals are PERSONAL INJURY also sealed, but because the terminals are exposed the DO NOT USE these products as safety or emergency corresponding degree of protection is IP00. stop devices or in any other application where failure of the product could result in personal injury. MOUNTING INFORMATION Failure to comply with these instructions could result Mounting Screw Screw Tightening in death or serious injury. hole size Type* Size Torque (max.) 3,1 mm Pan head 3 mm 2,9 kg-cm CAUTION 2.6 in-lb 2,9 mm Pan head 4 2,9 kg-cm SWITCH DAMAGE (-K option) 2.6 in-lb Wiring must be rated to meet or exceed circuitry *To prevent loosening of screws, use spring washers requirements. under screw heads and thread lock adhesive. Connecting circuitry must not exceed switch rating. Wiring connections must be properly secured. Turn OFF the power supply before mounting or removing Do not exceed recommended soldering time or the switch, wiring, or performing maintenance or temperature. inspection. Failure to do so may result in electric shock. Do not contact switch housing with soldering device. Mount the switch onto a flat surface. Mounting on an Do not exceed recommended mounting screw tightening uneven surface may cause deformation of the switch, torques. resulting in faulty operation or damage. Discontinue use if switch has been damaged or cover Use an operating device with low frictional resistance removed. and of a shape that will not interfere with the plunger seal Do not apply side loads to actuator or exceed specified otherwise the plunger may be damaged or the sealing travel limits. may deteriorate. Do not operate or store in areas where corrosive gases Position the operating device perpendicular to the such as hydrogen sulfide are present. actuator/pushbutton to prevent side loading of the switch Failure to comply with these instructions may result actuator or pushbutton. in product and/or property damage. Position the operating device so that no force is applied to the pushbutton/actuator when the switch is in the free position. IMPROPER USE The operating device should be positioned so that when Do not use in hazardous environments where the switch is in the operating position it should move the flammable or explosive gases or liquids such as actuator no less than 70% of the total travel. Setting the gasoline or thinners, etc., are present. travel position so that less than 70% of the total travel is Failure to comply with these instructions will result in used may cause poor contact or welding conditions due death or serious injury. to an insufficient contact switching force. The operating device should never force the GENERAL INFORMATION actuator/pushbutton to exceed the total travel position. MICRO SWITCH V15W Series watertight miniature WIRING INFORMATION TERMINAL VERSIONS switches are precision snap-action contact mechanisms Connect wires firmly to terminals. enclosed in watertight plastic cases. Switch actuation Replace wires that have damaged insulation. triggers the mechanical closure of the switchs contacts. Use properly sized spade terminals. A small amount of arcing between the contacts during Use wire rated for the applications electrical load and contact closure occurs during normal operation. In order applications temperature to obtain desired switch performance, the switch must be Provide strain relief when a potential exists for forces to chosen based on the mechanical, electrical and be transferred from the lead wires to the switch terminals environmental conditions of the application. Do not use this product in water. Although molded lead wire versions carry an ingress protection rating of IP67 according to the test conditions of IEC 529, this test is to check the ingress of water into the switch enclosure after submerging the switch in water for a given time. Sensing and Control Issue 2 MICRO SWITCH V15W Series Watertight 50066512 Miniature Switches WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of The switch is sealed around the terminals. However, live defective materials and faulty workmanship. Honeywells terminals should never be exposed to water. Use standard product warranty applies unless agreed to otherwise by appropriate sealed connectors or mount the switch in a Honeywell in writing please refer to your order sealed enclosure so that the terminals are not exposed acknowledgement or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell to water. during the period of coverage, Honeywell will repair or replace, at its option, without charge those items it finds defective. The WIRING INFORMATION - PRE-LEADED VERSIONS foregoing is buyers sole remedy and is in lieu of all other Provide strain relief when a potential exists for forces to warranties, expressed or implied, including those of be transferred from the lead wires to the switch. merchantability and fitness for a particular purpose. In no When wiring molded lead wire models, ensure that there event shall Honeywell be liable for consequential, special, is no weight on the wire and that there are no sharp or indirect damages. bends. While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to CIRCUIT INFORMATION determine the suitability of the product in the application. A circuit diagram is included on the switch case labeling Specifications may change without notice. The information we each of the terminals/wires. The normal position supply is believed to be accurate and reliable as of this printing. corresponds to the switch plunger in its released position. However, we assume no responsibility for its use. SALES AND SERVICE Honeywell serves its customers through a worldwide network of sales offices, representatives and distributors. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact your local sales office or: SOLDERING GUIDELINES E-mail: info.sc honeywell.com When hand soldering the switchs terminals, do not Internet: www.honeywell.com/sensing Phone and Fax: exceed five seconds at 350 C 662 F . Contacting the Asia Pacific +65 6355-2828 +65 6445-3033 Fax switch housing with the soldering device may damage Europe +44 (0) 1698 481481 +44 (0) 1698 481676 Fax the switch housing. Solder joints must not be moved for Latin America +1-305-805-8188 +1-305-883-8257 Fax USA/Canada +1-800-537-6945 +1-815-235-6847 at least one minute after soldering. +1-815-235-6545 Fax Do not try to clean the switch with a solvent or similar substance after the soldering process. ENVIRONMENTAL OPERATING CHARACTERISTICS Operating -40 C to 85 C -40 F to 185 F temperature range Humidity 95% max. Rate of actuation 0.1 mm/s to 1000 mm/s Operating frequency 30 operations/minute max. (electrical) Operating frequency 200 operations/minute max. (mechanical) Sensing and Control Honeywell 1985 Douglas Drive North 50066512-002-EN IL50 GLO Golden Valley, MN 55422 May 2014 sensing.honeywell.com Copyright 2014 Honeywell International Inc. All rights reserved.