MicroSmart Pentra RS232 Communication Module Features Up to 5 modules can be added to a MicroSmart Pentra Slim CPU Allows MicroSmart Pentra Slim to communicate with up to 7 serial devices Up to 3 modules can be added to a MicroSmart Pentra All-In-One CPU allowing communication with up to 5 serial devices. Communicate with HMIs, variable frequency drives (VFD), barcode readers, RFID equipment, printers, additional CPUs, displays, PCs, web servers, etc. Screw termination for easy wiring The communication circuit is isolated from the internal circuit allowing for high noise resistance Maximum baud rate: 38.4 kbps Specifications Communication Specifications 1200, 2400, 4800, 9600, General Specifications Baud Rate (bps) 19200, 38400 Number of Channels 1 Communication Data Bits 7 or 8 Synchronization Start-stop synchronization Parameters Parity Odd, even, none Electrical Characteristics EIA RS232C compliant Stop Bits 1 or 2 Maximum Delay in One Scan Approx. 4 ms Maintenance Possible (except for user pro- Operating Temperature 0 to 55C Communication gram download and upload) Protocol Operating Humidity 10 to 95% RH (no condensation) User Communication Possible Shielded multi-core cable 24AWG x 6 Recommended Cable Dielectric strength 2000 V/min Terminal Arrangement Specifications Terminal I/O Description Insulation resistance 100 M/km Maximum Cable Length 3m Request to Send (constant RS (RTS) Output voltage terminal) MC1.5/10-G-3.81BK (Phoenix Contact) Connector on Mother Board ER (DTR) Output Data Terminal Ready Applicable terminal block: FC4A-PMT10P (supplied) SD (TXD) Output Transmit Data Isolation from Internal Circuit Transformer isolated RD (RXD) Input Receive Data Slim type CPU module 5 max. Maximum Number of All-in-one 24-I/O type 3 max. (see note DR (DSR) Input Data Set Ready Communication Modules CPU module below) SG (SG) Signal Ground 85 mA (5V DC) NC No connection Internal Current Draw 0 mA (24V DC) Functional ground (can be used Weight Approx. 100g as junction terminals of func- Note: Use only the Slim MicroSmart Pentra CPU to connect to the expansion RS232C communication modules in tional ground not connected to combination with the function modules listed below (not applicable to the FC5A-C24R2 all-in-one module). the internal circuit) Function Module Type No. Mounting Hole Layout Dimensions (mm) FC4A-L03A1, FC4A-L03AP1, FC4A-J2A1, 23.5 3.8 23.5 14.6 70.0 Analog I/O Module FC4A-J4CN1, FC4A-J8C1, FC4A-J8AT1, 6.3 FC4A-K1A1, FC4A-K2C1 AS-Interface Master Module FC4A-AS62M Notes 1. WindLDR version 5.10 or higher is required. 2. Applicable FC5A CPU firmware is version 1.10 or higher. 3. WindLDR version 5.10 allows for firmware upgrade. 3.0 8.5 mm when the clamp is pulled out. IDEC Corporation 1175 Elko Drive Sunnyvale, CA 94089 800-262-IDEC (4332) Fax: 408-745-5258 www.idec.com 2007 IDEC Corporation. All Rights Reserved. 2-4.3 4.5 90.0 90.0 103.0X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Idec manufacturer: Other Similar products are found below : LT7A-XE-G LT7A-XE-R LT7B-A250 LT7B-A250FB LW6L-M1C24MG FB1T-000Z FB1W-HW1B-V411R-EMO-2 FB1W-XW1E- BV411MR FB1W-XW1E-BV413MR FB3W-413Z FC2A-KP1C FC4A-J8AT1 FC4A-T16S3 FC5A-C16R2C MM-SMART-24 MM- SMART-40 FT1A-C12RA-S FT1A-C12RA-W FT1A-C14SA-B PF3S-BP12 PS3X-D24AFG PS3X-Q12AFG GT3A-3AD24 GT3F- 2EAD24 GT3S-2AF20 GT3W-A16AD24 GT3W-A33AF20N ABD302N-R ABD410N-R ABFD411N-G ABN4F11-G HE2B-M211PB HE2G-21SH HE9Z-D3B HG9Z-2A1 HG9Z-XC300 ACSNO-6123-FB-C6002 RH3V2-UAC240V DFAN-031-B AL6M-LK1-G AL6M-P3- R AL6Q-M13-W AL6Q-M23P-QG ALFD29901DN-G-24V ALFN22211DNG-U ALFW224611D-W ALNE8811-G ALQW2B24611D-G ALW212611-G ALW22211DG