SpectraDIL - 014 style SDS, SDC, SDD ranges This series offers standard programme setting Principal Electrical and Performance Data switches to suit applications where end stacking at 20C 70% R.H. up to any number of switches without missing a Contact Ratings: Non Switching: 100Vac, 5A pitch is required. Switching: 1V to 100V, 1A to 1A up to 10VA. Initial Contact Resistance: (at 10mV, 10mA max.) Large numerals and actuators plus EIA colour Typical: 10m . Max. 20m . coded sliders with open access to them. Insulation Resistance: (at 500Vdc min.) 10,000M . Base sealed for flow soldering. If immersion Life: For the first 1000 closures the standard deviation of the washing, use 023 series. change in resistance from the mean is usually less than 1m . Mechanical wear out of the sliding actuator is usually observed 1m hard gold plated wiping contact gives high after 10,000 operations. reliability in low level circuits. Dielectric Strength: 1 minute: 500Vrms 50Hz. Capacitance Between Open Contacts: < 1pf at 1KHz. If you have a volume requirement for a Temperature: Operating range for continuous electrical use product variant not shown on this sheet and manual operation is restricted to -55C to +100C for please contact us. standard products. SpectraDIL ON/OFF s.p.s.t SDS 014 series Humidity: BS 2011 Test Ca: 56 days. Number of Part Nos Length Bump: BS 2011 Test Eb: No contact interruptions > 1s during s.p.s.t SDS-plus mm 2 4000 bumps at 390m/s (40g). suffix max 1 1-014 3.1 Acceleration: BS 2011 Test Ga: No contact interruptions > 1s 2 2-014 5.0 2 during test at 980 m/s (100g). 4 4-014 10.1 6 6-014 15.0 Vibration: BS 2011 Test Fc: 10 to 2000Hz. No contact 8 8-014 20.1 2 interruptions > 1s during test at 147m/s (15g) or 1.0mm 10 10-014 25.2 displacement amplitude. 2 Shock: BS 2011 Test Ea: 980 m/s (100g). No contact SpectraDIL CHANGEOVER s.p.d.t. SDC 014 series interruptions > 1s during test. Number of Part Nos Length Soldering: solderability: < 2 seconds to wet at 235C as per s.p.d.t SDC-plus mm suffix max IEC 68 and BS 2011 Test T, solder bath method. 1 1-014 5.0 Resistance to soldering heat as per IEC 68 and BS 2011 10 2 2-014 10.1 3 3-014 15.0 seconds satisfactory at 260C when mounted on 1.5mm PCB. 4 4-014 20.1 Please note: BS 2011 is now superseded by BS EN 60068. 5 5-014 25.2 SpectraDIL GANGED ON/OFF d.p.s.t SDD 014 series Number of Part Nos Length d.p.s.t SDD-plus mm suffix max 1 1-014 5.0 2 2-014 10.1 3 3-014 15.0 4 4-014 20.1 5 5-014 25.2 SpectraDIL - 014 styleX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for DIP Switches/SIP Switches category: Click to view products by Illinois Tool Works manufacturer: Other Similar products are found below : 09.400BP.04 106-EM04-EV 106-EM08-EV 106-LP04-EV 106-LPD04-EV 106-SDN06-EV 1-1437507-0 1-1437507-6 1-1571983-1 1- 1571983-3 1-1571983-4 1-1571983-5 1-1571998-3 1-1571999-1 1-1571999-6 1-161347-2 1-1825002-0 1-1825002-3 1-1825002-4 1- 1825002-7 1-1825002-8 1-1825006-1 1-1825006-3 1-1825006-6 1-1825006-7 1-1825006-9 1-1825007-0 1-1825007-3 1-1825008-0 1- 1825008-2 1-1825013-1 1-1825013-7 1-1825013-9 1-1825057-0 1-1825058-3 1-1825058-6 1-1825058-9 1-1825059-1 1-1825059-2 1- 1825059-3 1-1825059-4 1-1825059-7 1-1825059-8 1-1825059-9 1-1825190-0 1-1825286-0 1-382394-5 1-382394-7 1-435802-5 1-435802- 6