20ALMDC-AXXX-8 IMO

Y E A R G U Loop Powered Trip Amplifiers 20ALM The 20ALM is an input loop powered trip amplifier, deriving its power from the input signal High or low alarm option Low voltage drop Setpoints available on front panel as 0.4 to 2V signal (4 to 20mA) LED indication of alarm Unique low cost solution Options and ordering codes Description The output of the 20ALM is a single pole, normally open, solid state relay 20ALM - 115VAC - AXXX - 8 which can be configured to close either above or below the adjustable setpoint. The switched output can be connected to any potential within 1kV of the transmitter supply, while transients of 2.5kV can be withstood. Options The relay is designed to switch AC or DC. 115VAC rated contacts 115VAC The trip amplifier is typically used to activate a warning or control system 24VAC/DC rated contacts DC override when a sensor output goes above or below a pre-set limit. Alternatively, the unit can be used for simple on/off control, having a built in switching hysteresis. Dimensions (mm) The device is housed in an ultra-compact DIN-Rail mounted enclosure, only 63mm 18mm wide. Recommended operating conditions 12 Input current 4-20mA Relay contact voltage 24Vac/dc or 110Vac Relay current (max) 300mA 24Vdc 130mA 110Vac Output resistance 5 (on) 24V type 24 on 110Vac type Environmental conditions Storage temperature -40-70C Operating ambient 0-55C 34 Relative humidity 0-90% RH 1 Connection details 4-20mA 3 1. Relay output -ve 3. Input channel +ve 2. Relay output +ve 4. Input channel -ve N.O. or N.C. solid 3.4V state relay output 4 2 Specification Parameter Min Typ Max Comments Supply voltage Loop power Supply current 4mA 20mA Full scale volt drop 3.4V 3.5V At 20mA input Relay type 1 current 315mA Rated at 24Vdc/ac Relay type 2 current 130mA Rated at 110Vac Output resistance ON 5 /24 24V/110Vac relay type Setpoint hysteresis 50A Other values available Trip point accuracy 0.25% Temperature coefficient 100ppm/C Trip point drift 100ppm/C Relay time response 10ms Operating ambient 0C 55C Relative humidity 0% 90% Isolation voltage 1kV Surge voltage 2.5kV for 50S Transient of 10kV/S Notes Setpoint is adjusted by 20 turn potentiometers on the front panel. Setpoint can be checked by measuring the 0.4 to 2V (4 to 20mA) voltage on the front panel terminals. High or low alarm is selectable using internal link. Closed output contact is indicated by a red LED on the front panel. 20ALM/03/03 www.imopc.com A R A N T E E 18mm 58mmX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for imo manufacturer: Other Similar products are found below : 20.155MV/12-E MC14N-S-10110AC MB09-S-10=24 DPS-1-030-24 SRF-1C-SL-12VDC MB09-S-1024 LDC18RRS SFSYE0111 21.1500M/6-E 20.3304M/2-E 21.910M/5-E 20.95MA/2-E 21.95MHF/2-E PE69-4032 DPS-1-060-24 CS20A-A2 CS20A-U1 VFC02 MSSTC11DA06 20.95MHF/3-E B3T10 XKL-040-21 20.3304M/4-E SRDH-1A-SL-24VDC 20.2500M/5-E 21.155MH/12 SRRHN-2CN- SL-12VDC 20.920M/5-E MC10N-S-10110AC 21.1550MF/8-E 20.910M/6-E 20.95MH/3-E 21.95MV/3 MA05-S-01230AC SRRHN-2CN- SL-5VDC LB69-4040 20.3001M/6 21.1500M/3-E SFSYE0311 21.95MHF/6-E 20.95MV/2-E 20.155MV/4-E 20.155MH/4-E 20.950M/2-E MT5 1-50-FAR BS3P3REDO MB12-S-10=24 MA05-S-1024DC 20.155MVF/8-E 20.2500MV/8-E