DK-START-5AGXB3N Intel

Page 1 of 4 Arria V GX Transceiver Starter Kit from Altera Ordering Information Transceiver Starter Kit Contents Starter Board Photo Related Links The Altera Arria V GX Transceiver Starter Kit provides a complete design environment that includes all the hardware and software you need to develop cost-sensitive FPGA applications immediately. The development kit is RoHS compliant. The development kit features the following: Arria V GX FPGA360KLE, F1517 package, 24X6.6G XCVRs, C4 speed grade One I/O expansion slotsone high-speed mezzanine card (HSMC) 16 MB of SDRAM memory High-definition multimedia interface (HDMI) and serial digital interface (SDI) connections SMAs Ordering Information Table 1. Arria V GX Transceiver Starter Kit Ordering Code and Pricing Information Ordering Code Price Ordering Information DK-START- The Arria V GX Transceiver Starter Kit features a 5AGXB3 Engineering Sample (ES) device and a 1-year 5AGXB3NES license for the Quartus II design software. Contact your local Altera distributor to place your order. Transceiver Starter Kit Contents The Arria V GX Transceiver Starter Kit features the following: Arria V GX FPGA development board (see Figure 1) FPGA: Arria V GX 5AGXFB3H4F35C4NES System controller: MAX V 5M2210ZF256C4N Power monitor GUI Single analog-to-digital converter (ADC), eight channels Non-isolated power rail Fast passive parallel (FPP) x16 mode through parallel flash loader (PFL) Control and status registers TM Embedded USB-Blaster II: MAX II EPM570GM100C4N HDMI 1.3 TX x4 XCVR, 3.4 Gbps (max by spec) and 340 MHz TX clock (by spec) HDMI TX connector TI HDMI level shifter SN75DP130 Level shift XCVR PCML 1.5V <-> TMDS level DDC and HPD <-> HDMI compliant level Data channel up to 5.4 Gbps HDMI 1.3 only needs a maximum of 3.4 Gbps Clock channel up to 340 MHz enough to support 3.4 Gbps data rate HDMI specification: clock period = 10x of UI Requires 100 MHz clock input at CLKIN to generate the TX clk and core logic SDI 3G x1 XCVR TX/RX loopback x2 SMB connectors and cable (cable not included in kit) 7/6/2012Arria V GX Transceiver Starter Kit Page 2 of 4 Up to 2.97 Gbps Uses National Semiconductor driver/receiver LMH0384SQ/LMH0303SQx Requires 148.5 MHz and 148.35 MHz at XCVR refclk to support US and EU standard respectively Use VCXO to fine tune and lock to the recovered CDR frequency Requires 125 MHz CLKIN for core logic HSMC x8 XCVR up to 6.375 Gbps Not complied to PCI Express (PCIe ) HIP pin assignment x4 CMOS x17 differential using dedicated TX/RX channel x2 low-voltage differential signalling (LVDS) clock in x2 differential clock out I2C JTAG Minimum current support 2A 3.3V 1A 12V Dedicated clock domain from Si 5338 clock generator for xcvr refclk HSMC loopback with BTS GUI SMA 7x XCVR TX/RX channel 1x LVDS clock input Dedicated clock domain from Si 5338 clock generator for xcvr refclk DDR3 SDRAM x32 Micron MT41J64M16JT-15E DDR3 SDRAM 8MX16X8 Two devices: 2 x16 width = x32 BTS DDR3 SDRAM GUI using Uniphy and high performance (HP) controller II SSRAM 1024k x18, 18 Mb ISSI IS61VPS102418A Shared address or data with flash User IO LCD character x4 DIP switch x3 PB x4 LED Configuration FPP x16 mode Dual flash 512Mbit Numonyx PC28F512P30BF (52 MHz F ) MAX JTAG header Embedded USB Blaster II Cypress Microcontroller CY7C68013A as USB PHY 2.0 MAX II Ethernet 10/100/1000 Base-T RJ-45 connector, on-board LED for link status Marvell Ethernet PHY 88E1111 Requires 100 MHz and 125 MHz clock from CLKIN Figure 1: Arria V GX Starter Board with a 5AGXB3ES FPGA Device 7/6/2012