Programmer for drivers and controllers PRG-MUL2 Rev. D Description Supports DALI interface driver Programming Supports 0-10V Programmable Driver Programming Supports Other Controllers (TDD-ANPNx, SDD-AAPNx) Off-line programming capability Auto programming Mode Selectable tools for mass programming Model Name Description Model Number nd Multi programmer 2 Generation Multiple Programmer PRG-MUL2 Interface Specifications Parameters Min. Typ. Max. Note Vaux Voltage 9.8 V 12 V 13.2 V Auxiliary Supply Voltage Vaux Source Current 0 - 20 mA Auxiliary Supply Current (Red LED,Green LED)Voltage 1.6 V - 3 V Voltage of External LED indicator (Red LED,Green LED)Current 0 - 10 mA Current of External LED indicator (Push Button)Voltage - - 3.3 V Voltage of External Push button (Buzzer)Voltage - - 5 V Voltage of External Buzzer (Buzzer)Current - 30 mA - Current of External Buzzer 5V USB current consumption - - 300 mA Use USB charger or PC USB Function Description Off-line Programming At PC end, the upper software can download the configuration to the programmer, then only 5V power supply is needed to program the drivers or controllers. Automatic Programming When this function is enabled, after connecting the programming leads to the programmer, it will download the configuration to the controller or driver. Long Push Button(5s<T<10s), the Automatic function will be disabled or enabled. When the function has been turned on, the Red LED will flicker 2 times, each time lasts 0.5 second. When the function has been turned off, the Green LED will flicker 2 times, each time lasts 0.5 second. Buzzer The programmer provides a port for connecting to an external Buzzer if needed. When programming has finished successfully, the buzzer will beep for 0.5 seconds. 1 / 6 Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales inventronics-co.com Programmer for drivers and controllers PRG-MUL2 Rev. D Long Push Button(T>10s), it will enable or disable the buzzer function. When the buzzer function is enabled by above action, the buzzer will beep 2 second, or it will beep 0.5s that means the function is disabled. Product Series Matching Verify Before starting the programming, the programmer will read the driver model information. If the configuration model does not match the driver model, the upper software will show fail message, and the red LED will turn on. The matching function is selectable at PC end. The default setting is on. Notes: 1. 0~xV controller does not support matching function for it only supports one direction protocol. 2. Green LED indicates successful programming. Red LED indicates failed programming. LED indicator mode Manual Mode Automatic Mode Status Red LED Green LED Red LED Green LED Start up flicker N times in 0.5s flicker N times in 0.5s flicker N times in 0.5s flicker N times in 0.5s Flicker continuously Standby off on off (per 1s) Programming off Flicker continuously off Flicker continuously Succeed off on off on Failed on off on off Notes: the N in the table indicate the programming mode, refer to the below. N=1 Off-line programming mode for 0~xV controller. N=2 Off-line programming mode for Timer controller. N=3 Off-line programming mode for constant power driver. N=4 Off-line programming mode for DALI supported driver. Environmental Specifications Parameters Min Typ Max Note Humidity: 10%RH to 90%RH. Operating temperature -20 - +50 No condensation. Humidity: 5%RH to 90%RH. Storage temperature -40 - +70 No condensation. General Specifications Parameter Min. Typ. Max. Notes Dimensions Inches (L W H) 3.35 1.85 0.83 Millimeters (L W H) 85 47 21 Net Weight - 45 g - Note: All specifications are typical at 25 C unless otherwise stated. 2 / 6 Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 sales inventronics-co.com