TCXO Specification Part No. + Packaging: LFPTXO000002Bulk Customer Part: Description Sub 1ppm performance TCXO/VCTCXO, a single chip oscillator and analogue compensation circuit operating over an extended temperature range. Its ability to function down to a supply voltage of 2.4V and low power consumption make it particularly suitable for mobile applications. No ref voltage, ageing adj option Model CFPT-9006 iss:14.01-1A Model Issue number 14 Frequency Parameters Frequency 12.80MHz Frequency Tolerance 1.00ppm Tolerance Condition 25C 1.00ppm Frequency Stability Operating Temperature Range -40.00 to 85.00C Acceleration sensitivity (Gamma vector, 3-axes, 30-1500Hz): <2 ppb/g typ Outline (mm) Ageing: 1ppm max in 1st year, frequency 20MHz 3ppm max for 10 years (including the 1st year), frequency 20MHz 2ppm max in 1st year, frequency >20MHz 5ppm max for 10 years (including the 1st year), frequency >20MHz Supply Voltage Variation (10% change reference to frequency at nominal supply voltage): 0.2ppm typ Load Variation (5pF change reference to frequency at nominal load): 0.2ppm typ After Reflow: 1ppm max Electrical Parameters 3.3V 10% Supply Voltage Supply Current (typical): HCMOS: 1+Frequency(MHz)*Supply(V)* Load(pF) Test Circuit +15 *1E3mA i.e 20MHz, 3.3V, 15pF 3mA Calculation: 1 + (20 x 3.3 x (15+15) x 0.001 ) = 2.98mA Sales Office Contact Details: UK: +44 (0)1460 270200 France: 0800 901 383 Email: info iqdfrequencyproducts.com Germany: 0800 1808 443 USA: +1.760.318.2824 Web: www.iqdfrequencyproducts.com Printed on 2 Dec 21 13:55 using Part Data Sheet V1.0018 Page 1 of 3TCXO Specification Part No. + Packaging: LFPTXO000002Bulk Customer Part: Frequency Adjustment Optional reference voltage output on pad 1, suitable for potentiometer supply or DAC reference: 1. No output (standard option) 2. 2.2V for min Vs>2.4V 3. 2.7V for min Vs>3.0V Maximum load current (mA) = Vref/10 For manual frequency adjustment connect an external 50k potentiometer between pad 1 (Reference Voltage) and pad 4 (GND) with wiper connected to pad 10 (Voltage Control). Please specify reference voltage as part of the ordering code. Standard Voltage Control Ranges: Without Reference Voltage Vs=3.3V 1.65V1.0V With Reference Voltage Vs=0V to Vref Linearity: 1% max Slope: Positive Input Impedance: 100k min Modulation Bandwidth: 2kHz min A. Standard Pulling Adjustment: 5ppm min, frequency 20MHz 7ppm min, frequency >20MHz B. No frequency adjustment initial calibration 25C 1.0ppm C. High Pulling 10ppm to 20ppm can be available depending on frequency and stability options (please contact an IQD Sales Office) Output Details HCMOS Output Compatibility Drive Capability 15pF Rise and Fall Time 8.0ns max Duty Cycle 45/55% VoL: <10% Vs VoH: >90% Vs Output Control Tri-state Operation: Logic 1 (>60% Vs) or no connection to pad 8 enables output Logic 0 (<20% Vs) to pad 8 disables output The tristate control (enable) pin has a internal 100k pull up resistor which allows the pin to be left unconnected if not required. When in tristate mode, the output stage is disabled, but the oscillator and compensation circuit are still active (current consumption typ. 1.0mA). Noise Parameters Phase Noise (typical 13.0MHz): -65dBc/Hz 1Hz -95dBc/Hz 10Hz -120dBc/Hz 100Hz -135dBc/Hz 1kHz -140dBc/Hz 10kHz -145dBc/Hz 100kHz Sales Office Contact Details: UK: +44 (0)1460 270200 France: 0800 901 383 Email: info iqdfrequencyproducts.com Germany: 0800 1808 443 USA: +1.760.318.2824 Web: www.iqdfrequencyproducts.com Printed on 2 Dec 21 13:55 using Part Data Sheet V1.0018 Page 2 of 3