Sure-Seal Sure-Seal Low cost, high reliability A one-piece resilient body and rugged multiple moisture seals make Sure-Seal connectors a natural for applications where outside contaminants must be excluded. Sure-Seal is reliable and uncomplicated. Only two parts are required to complete a connector: the connector body, and the contacts. Sure-Seal was developed to address Department of Transportation safety regulations for connectors used in automobiles. Since then, Sure-Seal has been successfully used in a broad range of environmental applications where a small, low cost connector is needed. These sealed connectors meet or exceed DOT requirements for shock, vibration, temperature cycling, salt water spray and immersion, petroleum derivatives, industrial gas, all the while insuring low milli-volt drop and low contact resistance. Existing applications include motorcycles, automobiles, boats, and a wide range of demanding off-road vehicle uses. Sure-Seal will operate in temperatures from -40F to +221F under conditions of high humidity, severe vibration, ice and mud. Sealing integrity is maintained with exposure to brake fluid, gasoline, diesel fuel, anti-freeze, ultraviolet, ozone, and steam. Wet, humid, or dirty environments Automotive Trucks and Buses Applications requiring a low cost, small and reliable Marine Off-road Vehicles sealed connector Appliances Industrial Machinery Low Installed Cost are required. Bodies mate using multiple Features One piece molded bodies and crimp resilient seals and will remain mated even contacts provide a low cost solution. under severe vibration and shock. In addition, these connectors can be easily Field Serviceable terminated by the user. The use of removable crimp contacts allows Water Submersible Sure-Seal connections to be changed or Not just splash-proof, but truly submersible modified in the field if necessary. for short periods of time. Sure-Seal will seal Polarized Against Mis-mates to the requirements of IP67 and DIN 400 50. Connector halves use both pin and socket Resistant to Automotive/Industrial contacts. The plug and receptacle must be Environments properly oriented for the connectors to Sure-Seal will operate in temperatures from mate. Raised indexing ribs in conjunction -40F to +221F under conditions of high with a stepped plane allow blind mating of humidity, severe vibration, ice and mud. the connector halves even in dark or Sealing integrity is maintained with exposure cramped spaces. to brake fluid, gasoline, diesel fuel, Three Sure-Seal Versions antifreeze, ultraviolet, ozone, and steam. Sure-Seal is available in three versions. The Wide Range of Wire Gauges and basic Sure-Seal line is the broadest and Current Carrying Capability ideal for most applications. Mini-Sure-Seal Up to 85 amps with wire gauges from size provides a slightly smaller connector in a 20 up to size 4 AWG wire. limited range of configurations. Power Sure-Seal is for single circuit, high power One-Piece Connector applications. Sure-Seal has a simple one-piece molded body. No other parts (other than contacts) Visit us at: www.suresealconnections.com 1111 See back cover for contact details www.PeiGenesis.com Specifications subject to change. Sure-Seal Technical MATERIALS & FINISHES Specifications Body Elastomeric material (Complete test data (PVC Nitrile standard. Also available in silicone & EPDM) available on Contacts Copper alloy page 26.) Plating Tin standard gold plating optional ELECTRICAL DATA Operating Voltage 400 Vac maximum Dielectric Withstanding Voltage 1,200 Vac at sea level Current rating 15 Amps (Sure-Seal ) 8 Amps (Mini Sure-Seal ) 85 Amps (Power Sure-Seal ) Insulator Wire Range Sizes 14 - 18 AWG (Sure-Seal ) 18 - 20 AWG (Mini Sure-Seal ) 4 - 10 AWG (Power Sure-Seal ) Contact Resistance 10 Milliohms maximum Insulation Resistance 100 Megohms (minimum) MECHANICAL Operating Temperature -40F to +221F (-40C to +105C) ~ Sealing ~IP67, DIN 400 50, 3 foot depth in 5% salt solution ~ 24 hours min. ~NEMA 6 p Wire Sealing Range See column 8 on contact chart, page 17 Insulation Strip Lengths See column 7 on contact chart, page 16 Mating Life 50 cycles minimum (stamped & formed) 100 cycles (machined) Salt Spray To MIL-STD-202D Method 101D Heat +221F (+105C) for 1000 hours (See test data page 26) Weather, Ozone, & Ultraviolet In accordance with ASTM D-1149 (100pphm) & ASTM D-1171 (outdoor exposure) Vibration 5 to 55 Hz .06 DA 1 hour radial & longitudinal axes Shock 50g 11ms, 30 cycles radial & longitudinal axes Contact Type Crimp: using hand or semi-automatic tooling Number of Circuits 1 to 10 Contact Insertion From rear with simple hand tool or simultaneous insertion of multiple contacts with semi-automatic insertion machine. Removable, 5 cycles minimum Contact Retention 7.5 lbs. (35N) minimum Polarization Stepped plane positive polarization, indexing ribs, and visual polarization all permanently molded into body Agency Listing UL (E176866) & CSA (LR109871-1) Color Black (alternate colors optional) 12 See back cover for contact details www.PeiGenesis.com Specifications subject to change.