CCM02 MK II TM EMV compatible Construction The CCM02 MK II connectors with Contacts Copper alloy landing contacts are dedicated for Plating Contact area : Gold alloy inlay applications where the reader usage is Terminals: Tin lead (2 min) high and the life span of the card is a Moldings High temp. thermoplastic UL 94V-0 rated key consideration. A connector with Spring Stainless steel contacts which land on the card, rather Card detection switch actuator Stainless steel than slide over it, should be specied so Mechanical Data as to minimize card wear. The CCM02 Number of Contacts 8 has been redesigned to give an even Mechanical life 500,000 cycles min higher performance in a compact, Card insertion force 10 N max affordable package. Card extraction force 1 N min / 10 N max Contact force 0.25 N min / 0.5 N max Features Card detection switch 0.8 N max for actuation (end travel switch actuation force actuates when card is 1,0 mm from 500,000 card insertion cycles. card stop) 1.8 N max for complete depression 2 The contacts do not touch the card Vibration Frequency 10 to 500 Hz. Acceleration 50m/s Duration 6 hours - amplitude 0,35 mm until it is almost fully inserted A Max electrical discontinuity 1s minimal wiping action removes any 2 Shock Peak value 500 m/s Duration 11 ms non-conductive material. 3 shocks in each direction of each axis Max electrical discontinuity 1 s The connector has been designed to Contact Electrical Data give a positive indication once the Insulation resistance 1,000 M min card has been fully inserted. Resistance 100 m max The reduced size of the contact base Current rating 10 A min / 1 A max saves PCB space, making the Dielectric strength 750 Vrms min connector more stable during surface Switch Electrical Data mounting, and creates an air gap Card detection switch Normally open between the contacts and card entry Contact resistance 100 m max slot, which reduces the risk of an Dielectric strength 250 Vrms min electrostatic transfer to the PCB. Current rating 1 mA min / 10 mA max For added reliability, the integrated card Maximum power 0.2 VA end-travel switch, which is normally Environmental Data open, is sealed against dust and grit. Operating temperature -40C to +85C By using an inlay nish in the contact Soldering temperature Temperature/time prole acc. to CECC00802 area, the life of the precious metal is para. 6.1, Fig. 3 with peak temperature 250C extended by more than 10 times that Damp heat IEC 512 test number 11c (10 days) of standard gold plating. Salt mist IEC 512 test number 11f (96 hours) Card detection switch Sealed IP 54 The contact area is spooned to reduce the risk of accidental (or deliberate) Ordering Code damage and to optimize the electrical Part Number Number of Termination PCB Packaging connection with the card. Contacts Tails Design Locating Multiple Snap-locks underneath the molding CCM02-2503 8 Through Hole 4 Board Lock (PCB 1.6 mm thick) 300 position and hold the connector on CCM02-2504 8 SMT 4 Board Lock (PCB 1.6 mm thick) 300 the PCB, and give additional support CCM02-2508 8 SMT 2 Pegs 300 to the contact terminals. CCM02-2511 8 Through Hole 4 Pegs 300 CCM02-2512 8 SMT 4 Pegs 300 The plastic moldings are made from a CCM02-2758 8 SMT 2 Pegs (without cover) 300 high temperature thermoplastic suited CCM02-2763 8 SMT 4 Board Lock + 2 Pegs 300 for infrared and convection soldering CCM02-2765 8 Through Hole 4 Board Lock (PCB 1mm thick) 300 processes. CCM02-2766 8 SMT 4 Board Lock (PCB 1mm thick) 300 Packaging TM EMV is a trademark owned by EMVCoLLC. 30 per tray, 10 trays per box. Dimensions are shown in mm Dimensions subject to change www.ittcannon.com 15CCM02 MK II Dimensional Drawings CCM02-2504 (8 contacts SMT - 4 board lock) 55,6 0,2 0,65 54,3 DETAIL A Embossed 1,8 Channel 19,12 5x 2,54 4x 4 Snap 0,2 A B Feet 52 0,20,15 50 (REF.) 38,5 (REF.) A Designation & Date-Code area SEE DETAIL A COUPE A-ACCM02 marking is optional 5,75 A Card stop CCM02-2504 XXXX A 10x Pick and place area Card insertion 1 4,150,3 Card entry 0,3 A 13 direction PCB Layout CCM02-2504 (8 contacts SMT - 4 board lock) (Component side) Plastic outline Contact foot area 0,8 x 1 SW SW Pad C1 C2 C3 C4 10 Card end travel Drawings shown for reference only. For other part switch terminals 0,8 x 1 numbers please consult your local Cannon Customer Service Center. 14 C5 C6 C7 C8 20 10x 4x +0,1 1,8 1,3 3,2 0 0,2 0,1 Contact location according to Unless otherwise stated, tolerances are 0,10 mm ISO 7816-2 Dimensions are shown in mm Dimensions subject to change www.ittcannon.com 16 1,6 PCB Thickness 38,5 6,25 0 25,3 3,1 1,7 1,5 1,5 19,12 21,66 24,2 26,74 29,28 31,82 3,81 3,81 8,84 0 27,6 -0,6 3,2 0,95 3,15 4,30,2 B 52 14 10 13,8 (REF.) 3,2 (REF.) 0 0 +0,4 0,8 13,8 13,8 3,2 -0,3 -0,3 -0,2 0,8 7,70,3 10,25 20 15,7 55,6 (REF.)