100R14Y105ZV4T Johanson

TANCERAM CHIP CAPACITORS TANCERAM chip capacitors can replace tantalum capacitors in many applications and offer several key advantages over traditional tantalums. Because Tanceram capacitors exhibit extremely low ESR, equivalent circuit performance can often be achieved using considerably lower capacitance values. Low DC leakage reduces current drain, extending the battery life of portable products. Tancerams high DC breakdown voltage ratings offer improved reliability and eliminate large voltage de-rating common when designing with tantalums. ADVANTAGES Low ESR Low DC Leakage Higher Surge Voltage Non-polarized Devices Reduced CHIP Size Improved Reliability Higher Insulation Resistance Higher Ripple Current APPLICATIONS Switching Power Supply Smoothing (Input/Output) Backlighting Inverters DC/DC Converter Smoothing (Input/Output) General Digital Circuits Typical ESR Comparison Typical Breakdown Voltage Comparison 10 100% 1.0 F / 16V Tantalum 1.0 F / 16V Tantalum 75% 1 50% 1.0 F / 16V TANCERAM 1.0 F / 16V TANCERAM 0.1 25% 0.01 0% 0 100 200 300 400 500 0.001 0.01 0.1 1 10 100 Frequency (MHz) DC Breakdown Voltage HOW TO ORDER TANCERAM 250 R18 Y 105 Z V 4 E VOLTAGE CASE SIZE DIELECTRIC CAPACITANCE TOLERANCE TERMINATION TAPE MODIFIER V = Ni barrier w/ 500 = 50 V W = X7R 1st two digits are Y5V Code Type Reel See Chart 100% Sn Plating 250 = 25 V X = X5R significant third digit E Plastic 7 Z = +80% -20% 160 = 16 V Y = Y5V denotes number of T Paper 7 X7R/X5R 100 = 10 V zeros. MARKING Tape specifications 6R3 = 6.3 V K = 10% 4 = Unmarked 474 = 0.47 F conform to EIA RS481 M = 20% 105 = 1.00 F P/N written: 250R18Y105ZV4E 16 www.johansondielectrics.com ESR (Ohms) % Distribution TANCERAM CHIP CAPACITORS CAPACITANCE SELECTION CASE SIZE VDC 1.0 F 2.2 F 4.7 F 10 F 22 F 47 F 100 F Inches (mm) DIELECTRIC L .040 .004 (1.02 .10) 0402 W L W .020 .004 (0.51 .10) W (X7R) T .025 Max. (0.64) 10 R07 * T E/B E/B .008 .004 (0.20.10) X (X5R) 6.3 ** Inches (mm) 25 Y (Y5V) * L .063 .008 (1.60 .20) 0603 16 W .032 .008 (0.81 .20) ** * T .035 Max. (0.89) 10 R14 * E/B .010.005 (.25.13) 6.3 ** Inches (mm) 25 * L .080 .010 (2.03 .25) 0805 16 W .050 .010 (1.27 .25) * T .060 Max. (1.52) 10 R15 * E/B .020.010 (0.51.25 ) 6.3 * Inches (mm) 25 * L .125 .010 (3.17 .25) 1206 16 W .062 .010 (1.57 .25) T .070 Max. (1.78) 10 R18 E/B .020 +.015-0.01 (0.51+.38-.25) 6.3 50 * Inches (mm) 25 L .125 .010 (3.18 .25) 1210 ** * W .095 .010 (2.41 .25) 16 ** T .110 Max. (2.8) S41 10 E/B .020 +.015-.010 (0.51+.38-.25) 6.3 WX Y W X Y WX Y W X Y WX Y W X Y WX Y DIELECTRIC CODE = NEW PART = HIGH VOLUME * ELECTRICAL CHARACTERISTICS X7R X5R Y5V Temperature Coefficient: 15% (-55 to +125C) 15% (-55 to +85C) +22%, -82% (-30 to +85C) Dissipation Factor: For 50 VDC: 5% max. For 50 VDC: 5% max. For 10 VDC: 16% max. For 25 VDC: 10% max. For 25 VDC: 10% max. For 6.3 VDC: 20% max. Insulation Resistance 100 F or 10 G, whichever is less (Min. 25C, WVDC) Dielectric Strength: 2.5 X WVDC, 25C, 50mA max. Capacitance values 22 F: 1.0kHz50Hz 1.00.2 Vrms Test Conditions: Capacitance values > 22 F: 120Hz10Hz 0.5V0.1 Vrms Other: See page 20 for additional dielectric specifications. 17 www.johansondielectrics.com