APPLICATION TOOLING Crimping tools and machines The arrow mark indocates the press that is applicable to the applicator. Crimping tools and machines Strip-crimp applicator Crimping applicator for end-feeding terminals for side feeding terminals MK-L MKS-SC Semi-automatic press Crimping applicator Crimping applicator for end-feeding flag terminals for side-feeding terminals Semi-automatic crimping machines (presses) contact a wire to a chain terminal each time a MKF-L MKS-L footswitch is pressed. AP-K2N Compact crimping applicator for side-feeding terminals MKS-LS Dimensions: (WLH)280480505mm Weight: Approx. 90kg(198lb) Power source: 100V AC, Single-phase 50/60Hz Pressure output: 14.7kN 1,500kg(3307lb) Dies: Applicator replacement 1 2Hand tools Crimping tools Crimping tools Hand tools Hand tools Extraction and Insertion tools for chain terminals for loose piece terminals for loose piece terminals Extraction tool Insertion tool YRS YC YRM YRF YRK YRK-EX series series series series series series Terminals and parts model Dimensions: Dimensions: Dimensions: Dimensions: Dimensions: Dimensions: (WL) 59224mm (WL) 70296mm (WL) 59224mm (WL) 70295mm (WLD) (WLD) 80305mm 7531425mm 7531425mm number in alphabetical order Crimping tools It is the manual tool that is convenience to terminate very small quantity of contacts for prototype or maintenance. It is composed of two crimping dies for the conductor and insulation, and can be crimp easily. YRK and YRK-EX can be used for mass-production. Note: (1) These tools are for prototype tooling or repair. Extraction tool is used to extract Insertion tool allows contacts be inserted (2) YC tool has two crimping sections (A and B). YRS tool has also two crimping sections by inverting upper dies. contacts improperly inserted in the housing. in the housing. Be sure to check applicable wires before use. Since the dies are fixed, the crimping height cannot be adjusted. Therefore, some of the This tool greatly increases efficiency especially applicable wires described in this catalog may not be crimped properly. when thin wires are used. Before use, check for proper crimping (such as tensile strength, terminal/contact deformation). (3) These tools are not applicable to 2-wire crimping. (4) When hand crimping board-in terminals (SAN, SCN, SDN, SGN, SIN, SJN, SZN), care should be taken not to contaminate the solder tails of the terminals, as with greasy or oily fingers. If a solder problem arises, some cleaning of the tips of the terminal is advisable. (5) WC and JUC hand tools are provided by J.S.T.(U.K.) LTD. and contact them about the details of these hand tools. WC & JUC series Terminal in loose form . YRS series YC series YRM series YRF series YRK YRK-EX series JUK s Hand Tools model No. JK-SP/SS2*** YRS-370 KEJ-0.7 for plug, KEJ-0.4 for socket J-SP/SS1*** YRS-440 YC-440 J-BP/BS1*** DEJ-0.3 J-SP/SS2*** YRS-330 DEJ-0.3 LFO-1.0-250N JUCS-FO LFO-2.5-250N JUCS-FO MD-SP12** YRS-470 MEJ-06 MD-SP22** YRS-460 MEJ-06 YRS-231 YRM-232 RA-SC1290 RA-BC12** EJ-RA YRM-233 RF-SC22** YRM-230 RF-BC22** RPJ-SP/SS2331 YRS-331 EJ-RPJ SAA-21(T)-** YC-141 LAA-21(T-)** SAA-50(T)-** YC-182 LAA-50(T)-** SAA-51(T)-** YC-142 LAA-51(T)-** SAB-51(T)-** YC-142 LAB-51(T)-** SACH-003G-P0.2 YRS-1190 SACH-002GU-P0.3 YRS-858 SAN-002T-0.8A YRS-220 EJ-PH SAN-002T-0.8K SBH-001T-P0.5 YC-670R WC-670 BBH-001T-P0.5 SBHL-002T-P0.5 YRS-857 SBHM-001T-P0.5 YC-670R BBHM-001T-P0.5 EJ-BHMR SBHS-002T-P0.5A YRS-852 EJ-BHS2 SBHS-002T-P0.5A EJ-BHS2 SBHSM-002T-P0.5 YRS-854 EJ-BHSW YRS-856 SBHT-002T-P0.5 EJ-BHT YRS-857 SBN-001T-1.0 YRS-170 YC-170R BBN-001T-1.0 SCN-001T-1.0K BCN-001T-1.0K YRS-191 YC-191R WC-191 SCN-001T-P1.0 BCN-001T-P1.0 SCS-41T-2.3 CSJ-23 SCSN-41T-P2.3 EJ-CSN SCZH-002T-P0.5 YRS-492 Note: Contact JST for wire range. 3 4