Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Floating Electrode Design with Flexible Termination System (FF-CAP), X7R Dielectric, 6.3 250 VDC (Commercial & Automotive Grade) Overview KEMETs Floating Electrode with Flexible Termination The FF-CAP complements KEMETs Open Mode, Floating capacitor (FF-CAP) combines two existing KEMET Electrode (FE-CAP), Flexible Termination (FT-CAP) and KEMET technologies Floating Electrode and Flexible Termination. Power Solutions (KPS) product lines by providing an ultimate The floating electrode component utilizes a cascading fail-safe design optimized for low to mid range capacitance internal electrode design configured to form multiple values. These devices exhibit a predictable change in capacitors in series within a single monolithic structure. capacitance with respect to time and voltage and boast a This unique configuration results in enhanced voltage and minimal change in capacitance with reference to ambient ESD performance over standard capacitor designs while temperature. Capacitance change is limited to 15% from allowing for a fail-open condition if mechanically damaged 55C to +125C. (cracked). The flexible termination component utilizes a conductive silver epoxy between the base metal and nickel In addition to Commercial Grade, Automotive Grade devices barrier layers of KEMETs standard termination system are available which meet the demanding Automotive in order to establish pliability while maintaining terminal Electronics Council s AECQ200 qualification requirements. strength, solderability and electrical performance. Both technologies address the primary failure mode of MLCCs flex cracks, which are typically the result of excessive tensile and shear stresses produced during board flexure and thermal cycling. Although neither technology can eliminate the potential for mechanical damage that may propagate during extreme environmental and/or handling conditions, the combination of these two technologies provide the ultimate level of protection against a low IR or short circuit condition. Ordering Information C 0805 Y 104 K 5 R A C TU Case Size Specification/ Capacitance Capacitance Rated Voltage Failure Rate/ Packaging/ 1 Ceramic Dielectric Termination Finish ( x ) Series Code (pF) Tolerance (VDC) Design Grade (C-Spec) 0603 Y = Floating Two significant J = 5% 9 = 6.3 R = X7R A = N/A C = 100% Matte Sn See 0805 Electrode digits and K = 10% 8 = 10 L = SnPb (5% PbPackaging 1206 with number of M = 20% 4 = 16 minimum) C-Spec 1210 Flexible zeros 3 = 25 Ordering 1812 Termination 5 = 50 Options 1 = 100 Tabl 2 = 200 A = 250 1 Additional termination finish options may be available. Contact KEMET for details. 1 SnPb termination finish option is not available on automotive grade product. One world. One KEMET KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1015 X7R FF-CAP SMD 11/9/2018 1 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.comSurface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Floating Electrode Design with Flexible Termination System (FF-CAP), X7R Dielectric, (Commercial & Automotive Grade) Packaging C-Spec Ordering Options Table Packaging/Grade Packaging Type Ordering Code (C-Spec) 1 Commercial Grade Bulk Bag Not Required (Blank) 7 Reel/Unmarked TU 7411 (EIA 0603 and smaller case sizes) 13 Reel/Unmarked 7210 (EIA 0805 and larger case sizes) 7 Reel/Marked TM 7040 (EIA 0603) 13 Reel/Marked 7215 (EIA 0805 and larger case sizes) 2 7 Reel/Unmarked/2 mm pitch 7081 2 13 Reel/Unmarked/2 mm pitch 7082 3 Automotive Grade 7 Reel AUTO AUTO7411 (EIA 0603 and smaller case sizes) 13 Reel/Unmarked AUTO7210 (EIA 0805 and larger case sizes) 2 7 Reel/Unmarked/2 mm pitch 3190 2 13 Reel/Unmarked/2 mm pitch 3191 1 Default packaging isBulk Ba. An ordering code C-Spec is not required forBulk Ba packaging. 1 The termsMarke andUnmarke pertain to laser marking option of capacitors. All packaging options labeled asUnmarke will contain capacitors that have not been laser marked. 2 The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case size devices. For more information regarding 2 mm pitch option seeTape & Reel Packaging Informatio. 3 Reeling tape options (Paper or Plastic) are dependent on capacitor case size ( x ) and thickness dimension. SeeChip Thickness/Tape & Reel Packaging Quantitie andTape & Reel Packaging Informatio. 3 For additional Information regardingAUT C-Spec options, seeAutomotive C-Spec Informatio. 3 All Automotive packaging C-Specs listed exclude the option to laser mark components. Please contact KEMET if you require a laser marked option. For more information seeCapacitor Markin. Benefits 55C to +125C operating temperature range Capacitance offerings ranging from 180 pF to 0.22 F Superior flex performance (up to 5 mm) Available capacitance tolerances of 5%, 10%, and 20% Floating Electrode/fail open design Commercial and Automotive (AECQ200) grades available Low to mid capacitance flex mitigation Non-polar device, minimizing installation concerns Lead (Pb)-free, RoHS and REACH compliant 100% pure matte tin-plated termination finish allowing for EIA 0603, 0805, 1206, 1210, and 1812 case sizes excellent solderability DC voltage ratings of 6.3 V, 10 V, 16 V, 25 V, 50 V, 100 V, SnPb termination finish option available upon request 200 V, and 250 V (5% Pb minimum) Applications Typical applications include circuits with a direct battery or power source connection, critical and safety relevant circuits without (integrated) current limitation and any application that is subject to high levels of board flexure or temperature cycling. Examples include raw power input side filtering (power plane/bus), high current applications (automobile battery line) and circuits that cannot be fused to open. Markets include consumer, medical, industrial (power supply), automotive, aerospace and telecom. KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1015 X7R FF-CAP SMD 11/9/2018 2 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.com