Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), U2J Dielectric, 10 100 VDC (Commercial & Automotive Grade) Overview The KEMET Flexible Termination (FT-CAP) Multilayer systems. FT-CAP complements KEMETs Open Mode, Ceramic Capacitor in U2J dielectric incorporates a unique, Floating Electrode (FE-CAP), Floating Electrode with Flexible flexible termination system that is integrated with KEMETs Termination (FF-CAP), and KEMET Power Solutions (KPS) standard termination materials. A conductive silver epoxy product lines provide a complete portfolio of flex mitigation is utilized between the base metal and nickel barrier layers solutions. of the KEMET standard termination system in order to establish pliability while maintaining terminal strength, Combined with the stability of U2J dielectric and designed solderability and electrical performance. This technology to accommodate all capacitance requirements, these flex- was developed in order to address the primary failure mode robust devices are RoHS compliant, offer up to 5 mm of of MLCCs flex cracks, which are typically the result of flex-bend capability and capacitance change limited to 750 excessive tensile and shear stresses produced during 20 ppm/C from 55C to +125C. These devices are lead- board flexure and thermal cycling. Flexible termination free, RoHS and REACH compliant without exception and are technology inhibits the transfer of board stress to the capable of withstanding multiple passes through a lead-free rigid ceramic body, therefore mitigating flex cracks which solder reflow profile. can result in low insulation resistance (IR) or short circuit failures. KEMET automotive grade capacitors meet the demanding Automotive Electronics Council s AEC-Q200 qualification requirements. Although this technology does not eliminate the potential for mechanical damage that may propagate during extreme environmental and handling conditions, it does provide superior flex performance over standard termination Ordering Information C 1206 X 104 J 3 J A C TU Case Size Specification/ Capacitance Capacitance Rated Voltage Failure Rate/ Packaging/ Ceramic Dielectric Termination Finish 1 ( x ) Series Code (pF) Tolerance (VDC) Design Grade (C-Spec) 0603 X = Flexible Two significant F = 1% 8 = 10 J = U2J A = N/A C = 100% Matte Sn See 0805 Termination digits and G = 2% 4 = 16Packaging 1206 number of J = 5% 3 = 25 C-Spec 1210 zeros. K = 10% 5 = 50 Ordering 1812 M = 20% 1 = 100 Options Tabl 1 Additional capacitance tolerance offerings may be available. Contact KEMET for details. Built Into Tomorrow KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1087 U2J FT-CAP SMD 11/3/2021 1 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.comSurface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), U2J Dielectric, 10 100 VDC (Commercial & Automotive Grade) Packaging C-Spec Ordering Options Table Packaging/Grade 1 Packaging Type Ordering Code (C-Spec) 1 Commercial Grade Bulk Bag/Unmarked Not required (Blank) 7 Reel/Unmarked TU 7411 (EIA 0603 and smaller case sizes) 13 Reel/Unmarked 7210 (EIA 0805 and larger case sizes) 2 7 Reel/Unmarked/2 mm pitch 7081 2 13 Reel/Unmarked/2 mm pitch 7082 3 Automotive Grade 7 Reel AUTO AUTO7411 (EIA 0603 and smaller case sizes) 13 Reel/Unmarked AUTO7210 (EIA 0805 and larger case sizes) 2 7 Reel/Unmarked/2 mm pitch 3190 2 13 Reel/Unmarked/2 mm pitch 3191 1 Default packaging is Bulk Bag. An ordering code C-Spec is not required for Bulk Bag packaging. 1 The terms Marked and Unmarked pertain to laser marking option of capacitors. All packaging options labeled as Unmarked will contain capacitors that have not been laser marked. The option to laser mark is not available on these devices. For more information see Capacitor Marking. 2 The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case size devices. For more information regarding 2 mm pitch option see Tape & Reel Packaging Information. 3 Reeling tape options (paper or plastic) are dependent on capacitor case size ( x ) and thickness dimensions. SeeChip Thickness/Tape & Reel Packaging Quantitie andTape & Reel Packaging Information. 3 For additional information regardingAUT C-Spec options, seeAutomotive C-Spec Information 3 All automotive packaging C-Specs listed exclude the option to laser mark components. The option to laser mark is not available on these devices. For more information seeCapacitor Marking. Benefits AECQ200 automotive qualified Low dissipation factor DF < 0.1% Low noise solution similar to C0G Low ESR and ESL High thermal stability High ripple current capability Preferred capacitance solution at line frequencies and into the MHz range Retains over 99% of nominal capacitance at full rated voltage Small predictable and linear capacitance change with respect to temperature Operating temperature range of 55C to +125C Capacitance up to 470 nF DC voltage ratings up to 100 V Lead (Pb)-free, RoHS and REACH compliant Non-polar device, minimizing installation concerns 100% pure matte Tin-plated termination finish allowing for excellent solderability KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1087 U2J FT-CAP SMD 11/3/2021 2 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.com