Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS, X7R Dielectric, 10 250 VDC (Commercial Grade) Overview KEMET Power Solutions (KPS) Commercial Series stacked are environmentally friendly and in compliance with RoHS capacitors utilize a proprietary lead-frame technology legislation. Available in X7R dielectric, these devices are to vertically stack one or two multilayer ceramic chip capable of Pb-Free reflow profiles and provide lower ESR, ESL capacitors into a single compact surface mount package. and higher ripple current capability when compared to other The attached lead-frame mechanically isolates the dielectric solutions. capacitor/s from the printed circuit board, therefore offering advanced mechanical and thermal stress performance. Combined with the stability of an X7R dielectric, KEMETs Isolation also addresses concerns for audible, microphonic KPS Series devices exhibit a predictable change in noise that may occur when a bias voltage is applied. A capacitance with respect to time and voltage and boast a two chip stack offers up to double the capacitance in minimal change in capacitance with reference to ambient the same or smaller design footprint when compared to temperature. Capacitance change is limited to 15% from traditional surface mount MLCCs devices. Providing up 55C to +125C. to 10 mm of board flex capability, KPS Series capacitors Benefits 55C to +125C operating temperature range Reliable and robust termination system EIA 1210, 1812, and 2220 case sizes DC voltage ratings of 10 V, 16 V, 25 V, 50 V, 100 V, and 250 V Capacitance offerings ranging from 0.1 F up to 47 F Available capacitance tolerances of 10% and 20% Higher capacitance in the same footprint Potential board space savings Ordering Information C 2220 C 106 M 5 R 2 C 7186 Rated Packaging/ Case Size Specification/ Capacitance Capacitance 2 Ceramic Voltage Dielectric Failure Rate/Design Leadframe Finish Grade 1 ( x ) Series Code (pF) Tolerance (VDC) (C-Spec) 1210 C = Standard Two K = 10% 8 = 10 R = X7R 1 = KPS Single C = 100% Matte Sn See 1812 significant M = 20% 4 = 16 Chip Stack Packaging 2220 digits and 3 = 25 2 = KPS Double C-Spec number of 5 = 50 Chip Stack Ordering zeros 1 = 100 Options Table A = 250 1 Double chip stacks 2 in the 13th character position of the ordering code) are only available in M (20%) capacitance tolerance. Single chip stacks 1 in the 13th character position of the ordering code) are available in K (10%) or M (20%) tolerances. 2 Additional leadframe finish options may be available. Contact KEMET for details. One world. One KEMET KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1020 X7R KPS SMD 6/28/2021 1 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.comSurface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS, X7R Dielectric, 10 250 VDC (Commercial Grade) Packaging C-Spec Ordering Options Table Packaging/Grade 1 Packaging Type 2 Ordering Code (C-Spec) 7 Reel (Embossed Plastic Tape)/Unmarked 7186 13 Reel (Embossed Plastic Tape)/Unmarked 7289 1 The termsMarke andUnmarke pertain to laser marking option of capacitors. All packaging options labeled asUnmarke will contain capacitors that have not been laser marked. The option to laser mark is not available on these devices. For more information seeCapacitor Markin. Benefits cont. Advanced protection against thermal Lead (Pb)-free, RoHS and REACH compliant and mechanical stress Capable of Pb-free reflow profiles Provides up to 10 mm of board flex capability Non-polar device, minimizing installation concerns Reduces audible, microphonic noise Tantalum and electrolytic alternative Extremely low ESR and ESL Applications Typical applications include smoothing circuits, DC/DC converters, power supplies (input/output filters), noise reduction (piezoelectric/mechanical), circuits with a direct battery or power source connection, critical and safety relevant circuits without (integrated) current limitation and any application that is subject to high levels of board flexure or temperature cycling. Markets include industrial, military, automotive and telecom. Qualification/Certification Commercial Grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in Table 4, Performance & Reliability. Environmental Compliance Lead (Pb)-free, RoHS, and REACH compliant without exemptions. KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1020 X7R KPS SMD 6/28/20212 2 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.com