VS-JV10A-K04 Kemet

Vibration Sensors VS Vibration Sensors Overview Applications KEMETs VS vibration sensors can detect vibrations in a Typical applications include abnormal vibration detection and wide frequency range from 10 Hz up to 15 kHz, through condition monitoring of production facilities of all industries, the effective conversion of vibrations to electrical signal motors, bearings, and pumps. by utilizing proprietary optimized piezo ceramic material and original vibration amplifying design. As no amplifier is required, it makes it very easy to embed. Its ability to detect even the faintest levels of vibration throughout a large sensing bandwidth makes it ideal for predictive maintenance and process control operations in industrial IoT, allowing for correction and data analysis flow to PLC, micro-computer or analyzers. Benefits Proprietary piezo ceramic material High sensitivity Large sensing bandwidth Built-in amplifier B Type J Type Integrated cable Unique detachable cable design for easy installation Ultra compact and ultra low-profile (8.4 x 11.4 x 2.9 mm) Compact and low-profile ( 18.0 11.0 mm) Easy to embed Waterproof and oil-resistant Case-insulated Current noise resistant VSJV10A VSBV203B One world. One KEMET KEMET Electronics Corporation KEMET Tower One East Broward Boulevard SE0209 VS 9/12/2019 1 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.comVibration Sensors VS Vibration Sensors Ordering Information VS- J V 10 A -K01 Model Output Series Sensitivity Interface Version Accessories Type Type 2 VS = Vibration B V = Voltage 10 = 10 m/s Blank = M8 connector type A Blank = Without accessory 2 Sensor J C = Current 20 = 20 m/s 3 = Integrated 3m cable type B K01 = Cable + magnet + stud for J type sensor K02 = Cable for J type sensor K03 = Cable + magnet for J type sensor K04 = Cable + stud for J type sensor Environmental Compliance All KEMET Vibration Sensors are RoHS and REACH Compliant. Article 33(1) of the REACH Regulation states that manufacturers and importers of articles (products) are required to notify their customers of the presence of any Substances of Very High Concern (SVHC) in their products exceeding 0.1% by weight and provide instructions on safe use of the product. KEMET Corporation reports regarding the Article 33(1) of REACH Regulation as follows: 1. Applicable Product: Vibration Sensors (VS series) 2. Report for the content of REACH SVHC list: The product(s) above contains a substance by more than 0.1wt% per product weight that was published in the 8th update of the REACH SVHC substances (December 19, 2012). 3. Regarding the safety of the vibration sensors (Piezoceramic products): The Piezoceramic that is used in this product becomes ceramic by sintering powder containing PZT as the main ingredient. It is chemically stable, with minimum risks toward the human body or environment within the intended use of the product. Please note that risks could occur in the case of inhalation or accidental oral uptake of powder ceramics. 4. Technical product information on the vibration sensors (Piezoceramic products): The manufacturing technique of the piezoceramic products whose main ingredient is Lead Titanium Zirconium Oxide (PZT) has been established, and there is no alternative material that can exhibit superior performance than PZT at this moment. Please note that the piezoceramic is listed as an exempt on RoHS (2011/65/EU) AnnexIII (7c.1). 5. The responsibility of piezoceramic manufacturers: Piezoceramic manufacturers report information regarding PZT containment in their products to the customers to obey the article 33 of the REACH regulation KEMET Electronics Corporation KEMET Tower One East Broward Boulevard SE0209 VS 9/12/2019 2 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.com