Keysight 34330A Current Shunt Instructions for Use Specifications The Keysight 34330A Current Shunt is Operating Environment: Indoor use Keysight Technologies, Inc. 2003 - 2014 a precision 0.001W resistor housed in a only plastic case surrounded by epoxy. Operating Temperature: 5 to 40 C Part Number: 34330-90001 Output is 1 mV per A of current Edition 3, September 2014 Operating Humidity: 0 to 80% RH passing through the shunt. Printed in Malaysia Storage Temperature: -30 to 70 C WARNING Keysight Technologies, Inc. Input Current: 5301 Stevens Creek Blvd. 15 A (continuous) Install the shunt in the multimeter voltage Santa Clara, CA 95052 USA 30 A (15 minutes, max) input terminals before use. Do not remove the shunt with a current source still con- Safety Limit, Max Voltage to Ground: nected, as there may be danger of shorting Safety Notices 60 Vdc, max the banana plugs to ground. Observe the 30 Vac (rms), max Do not attempt to repair this sealed device. current and voltage limits listed under Do not use this device for any purpose Voltage Sensitivity: 1 mV/A Specifications. other than indicated in these instructions. Accuracy (DC - 1 kHz): 0.3% The following simplified diagram shows Doing so may expose you to bodily injury Accuracy (1 kHz - 5 kHz): 5% or cause equipment damage. how the shunt is used: Do not install substitute parts or Assistance perform any unauthorized modification to the product. Return the product to an Key- Product maintenance agreements and sight Technologies Sales and Service other customer assistance agreements are Office for service and repair to ensure that available for Keysight Technologies prod- safety features are maintained. ucts. For assistance, contact your nearest Keysight Technologies Sales and Service Office. Further information is available on WARNING the Keysight web site at www.keysight.com/find/assist. A WARNING notice denotes a hazard. Insert the shunts banana-plug outputs It calls attention to an operating proce- into the main voltage inputs on the multi- Certification dure, practice, or the like that, if not meter (not the high ampere inputs). Then correctly performed or adhered to, connect the current source to be mea- Keysight Technologies certifies that this could result in personal injury or death. Do sured to the shunts input terminals product met its published specifications at not proceed beyond a WARNING notice (binding posts). The multimeter will read the time of shipment from the factory. The until the indicated conditions are fully the IR drop caused by the input current shunt is not subject to periodic calibration. understood and met. through the shunt. Warranty The precision resistance of the shunt is CAUTION 0.001W, so the voltage measured by the The material contained in this multimeter is equal to the current document is provided as is, and is A CAUTION notice denotes a hazard. multiplied by 0.001W. Thus, the voltage subject to being changed, without notice, It calls attention to an operating proce- reading sensitivity is 1 mV/A. For a in future editions. Further, dure, practice, or the like that, if not 15 A current, the voltage reading is to the maximum extent permitted by appli- correctly performed or adhered to, 15 mV. Select an appropriate voltage cable law, Keysight disclaims all warranties, could result in damage to the product or range on the multimeter. See your either express or implied with regard to loss of important data. Do not proceed multimeter Users Guide for further this manual and any information con- beyond a CAUTION notice until the information. tained herein, including but not limited to indicated conditions are fully understood and the implied warranties of merchantability met. and fitness for a particular purpose. Key- Cleaning Instructions sight shall not be liable for errors or for incidental or consequential Symbols Wipe with a soft cloth, moistened slightly damages in connection with the with water, if needed. furnishing, use, or performance of this doc- Refer to the operating ument or any information contained instructions for import- herein. Should Keysight and the user have ant safety information. a separate written agreement with war- ranty terms covering the material in this document that conflict with these terms, the warranty terms in the separate agree- ment will control. *34330-90001* 34330-90001X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Test Accessories - Other category: Click to view products by Keysight manufacturer: Other Similar products are found below : AO1026 AO1035 AO1051 AO1059 149116 149118 RS40 RS41 AO1030 AO1032 AO1036 AO1058 4742 KTS288540 11-32-2733 00415 00163 PACC-ZD005 PACC-ZD007 700M20TH 628824000 MPT-VF B3 15010A0A0100M0 B3 15050A0D01A2M0 B3 1505A00A01A1M0 B3 15060A0D0100M0 98-CAL020 MO-SCREEN 68-020-01P CVRF02 CPAK8 RT-ZA19 LCR-OPT-02 1-1437358-1 4408 POMONA DME D110 T1 LMLH 50 FLUKE PM9082/001 85392-12 ST18/SMAM/SMAM/72 HO720 BNC PROBES 310-064 45025 45028 CT2300 CC545 VT-1000 CT3041 VS-AVT-CABLE-08 6172A